ELTEX MES3108 - Page 120

120 MES3000 Ethernet switch series
bridge multicast forbidden
ipaddress
ip_multicast_address {add |
remove} {gigabitethernet
gi_port | tengigabitethernet
te_port | port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Deny the port to dynamically join the multicast group.
- ip_multicast_address—multicast IP address
- add—add port(s) into the banned list
- remove—remove port(s) from the banned list
Interface listing should be delimited with '–' and ','.
You have to register multicast groups prior to defining
the banned ports.
no bridge multicast forbidden
ip-address
ip_multicast_address
Restore the default value.
bridge multicast source
ip_address group
ip_multicast_address [[add |
remove] {gigabitethernet
gi_port | tengigabitethernet
te_port | port-channel group}]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Set the match between the user IP address and multicast address
in the multicast addressing table and statically add/remove
interfaces to/from the group.
- ip_address—source IP address
- ip_multicast_address—multicast IP address
- add—add ports to the source IP address group
- remove—remove ports from the source IP address group
no bridge multicast source
ip_address group
ip_multicast_address
Restore the default value.
bridge multicast forbidden
source ip_address group
ip_multicast_address {add |
remove} {gigabitethernet
gi_port | tengigabitethernet
te_port | port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Disable adding/removal of matches between the user IP address
and the multicast address in the multicast addressing table for the
specific port.
- ip_address—source IP address
- ip_multicast_address—multicast IP address
- add—disable port adding to the source IP address group
- remove—disable port removal from the source IP address group
no bridge multicast forbidden
source ip_address group
ip_multicast_address
Restore the default value.
bridge multicast ipv6 mode
{mac-group | ip-group |
ipsrcgroup}
-/mac-group
Specify multicast data transmission mode for IPv6 multicast
packets.
- mac-group—multicast transmission based on VLAN and MAC
addresses
- ip-group—multicast transmission with the filtering type based on
VLAN and the recipient address in IPv6 format
- ip-src-group—multicast transmission with the filtering type
based on VLAN and the sender address in IPv6 format
no bridge multicast ipv6 mode
Restore the default value.
bridge multicast ipv6
ipaddress
ipv6_multicast_address [[add |
remove] {gigabitethernet
gi_port | tengigabitethernet
te_port | port-channel group}]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Register multicast IPv6 address in the multicast addressing table
and statically add/remove interfaces to/from the group.
- ip_multicast_address—multicast IP address
- add—add ports to the group
- remove—remove ports from the group
Interface listing should be delimited with '–' and ','.
no bridge multicast ipv6
ipaddress
ipv6_multicast_address
Remove multicast IP address from the table.
bridge multicast ipv6
forbidden ip-address
ipv6_multicast_address {add |
remove} {gigabitethernet
gi_port | tengigabitethernet
te_port | port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Disable the connection for configured port(s) to multicast IPv6
address.
- ipv6_multicast_address—multicast IP address
- add—add port(s) into the banned list
- remove—remove port(s) from the banned list
Interface listing should be delimited with '–' and ','.
no bridge multicast ipv6
forbidden ip-address
ipv6_multicast_address
Restore the default value.
bridge multicast ipv6 source
ipv6_address group
ipv6_multicast_address [[add |
remove] {gigabitethernet
gi_port | tengigabitethernet
te_port | port-channel group}]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Set the match between the user IPv6 address and multicast
address in the multicast addressing table and statically
add/remove interfaces to/from the group.
- ipv6_address—source IP address
- ipv6_multicast_address—multicast IP address
- add—add ports to the source IP address group
- remove—remove ports from the source IP address group