ELTEX MES3108 - Page 142

142 MES3000 Ethernet switch series
snmp-server filter filter_name
[OID]
Remove SNMP filter rule.
snmp-server host
{ipv4_address | ipv6_address |
hostname} [traps | informs]
[version {1 | 2c | 3 [auth |
noauth | priv]}] community
[udp-port port] [filter
filtername] [timeout seconds]
[retries retries]
hostname: (1..158)
characters;
community: (1..20)
characters;
port: (1..65535)/162;
filtername: (1..30)
characters;
seconds: (1..300)/15
retries: (0..255)/3
Define settings for inform and trap notification message
transmission to SNMPv1/v2 server.
- community—community string for notification message
transmission
- version—define trap message type— trap SNMPv1, trap SNMPv2,
trap SNMPv3
- auth—specify the packet authenticity w/o encryption
- noauth—do not specify the packet authenticity
- priv—specify the packet authenticity with encryption
- port—SNMP server UDP port
- seconds—confirmation timeout, after which the inform message
will be re-send
- retries—number of inform messages' transmission attempts when
their confirmation is not received
no snmp-server host
{ipv4_address | ipv6_address |
hostname} [traps | informs]
Remove settings for inform and trap notification message
transmission to SNMPv1/v2/v3 server.
snmp-server v3-host
{ipv4_address | ipv6_address |
hostname} username [traps |
informs] {noauth | auth | priv}
[udp-port port] [filter
filtername] [timeout seconds]
[retries retries]
hostname: (1..158)
characters;
username: (1..24)
characters;
port: (1..65535)/162;
filtername: (1..30)
characters;
seconds: (1..300)/15;
retries: (0..255)/3
Define settings for inform and trap notification message
transmission to SNMPv3 server.
- noauth, auth, priv—authentication type used by SNMP v3
(noauth—w/o authentication, auth—authentication w/o
encryption, priv—encrypted authentication)
- port—SNMP server UDP port
- seconds—confirmation timeout after which the inform message
will be re-send
- retries—number of inform messages' transmission attempts when
their confirmation is not received.
no snmp-server v3-host
{ipv4_address | ipv6_address |
hostname} username [traps |
informs]
Remove settings for inform and trap notification message
transmission to SNMPv3 server.
snmp-server engineid local
{engineid_string | default}
engineid_string: (5..32)
characters
Create the local SNMP device identifier—engineid_string.
- default—when this setting is used, engineID will be created
automatically based on the device MAC address.
no snmp-server engineid local
Remove the local SNMP device identifier—engine ID.
snmp-server engineid remote
{ipv4_address | ipv6_address}
engineid_string
engineid_string: (5..32)
characters
Create the remote SNMP device identifier—engine ID.
no snmp-server engineid
remote {ipv4_address |
ipv6_address}
Remove the remote SNMP device identifier—engine ID.
snmp-server enable traps
-/enabled
Enable SNMP trap message support.
no snmp-server enable traps
Disable SNMP trap message support.
snmp-server enable traps
errdisable
-/disabled
Enable SNMP trap message transmission on the port state changes
to Errdisable
no snmp-server enable traps
errdisable
Disable SNMP trap message transmission on the port state changes
to Errdisable
snmp-server enable traps erps
-/enabled
Enable SNMP trap message transmission on the ERPS ring state
changes.
no snmp-server enable traps
erps
Disable SNMP trap message transmission on the ERPS ring state
changes.
snmp-server enable traps
flexlink
-/enabled
Enables SNMP trap message transmission on flex link interface pair
state changes.
no snmp-server enable traps
flex-link
Disables SNMP trap message transmission on flex link interface pair
state changes.
snmp-server enable traps
linkstatus
-/enabled
Enable SNMP trap message transmission on the port state changes.
no snmp-server enable traps
link-status
Disable SNMP trap message transmission on the port state changes.
snmp-server enable traps
macnotification change
-/disabled
Enables SNMP trap message transmission on changes in table of
learnt MAC addresses.