ELTEX MES3108 - Page 53

MES3000 Ethernet switch series 53
console(config)#
Table 5.28 —List of system time configuration commands in global configuration mode
Command
Value/Default value
Action
clock source sntp
-/external source is not
used
Use the external source for setting system time.
no clock source
Deny the utilization of the external source for setting system time.
clock timezone zone
hours_offset [minutes
minutes_offset]
zone: 4 characters/no
zone description;
hours_offset:
(12..+13)/0;
minutes_offset:
(0..59)/0;
Set the timezone value.
- zone—abbreviation of the phrase (zone description);
- hours_offset—hour offset from UTC zero meridian;
- minutes_offset—minute offset from UTC zero meridian.
no clock timezone
Restore the default value.
clock summer-time zone date
date month year hh:mm date
month year hh:mm [offset]
zone: (1..4)
characters/no zone
description;
week: (1..4, first, last);
day: (mon..sun);
date: (1..31);
month: (Jan..Dec);
year: (2000..2097);
hh: (0..23);
mm: (0..59);
offset: (1..1440)/60
min;
The daylight saving
change is disabled by
default.
Define date and time for automatic daylight saving change and the
set back process (for the specific year).
Zone description should be specified first, time for daylight
saving—second, and the set back time—third.
- zone—abbreviation of the phrase (zone description);
- hh—hours;
-mm—minutes;
- offset—quantity of minutes added during the daylight saving
change.
clock summer-time zone date
month date year hh:mm month
date year hh:mm [offset]
clock summer-time zone
recurring {usa | eu | {week day
month hh:mm week day month
hh:mm}} [offset]
Define date and time for automatic daylight saving change and the
set back process for each year.
- zone—abbreviation of the phrase (zone description);
- usa—set the daylight saving rules, used in US (daylight saving on
the second Sunday of March, set back on the first Sunday of
November, at 2am local time);
- eu—set the daylight saving rules, used in EU (daylight saving on
the last Sunday of March, set back on the last Sunday of October,
at 1am GMT);
- hh—hours;
-mm—minutes;
- offset—quantity of minutes added during the daylight saving
change.
no clock summer-time
Disable daylight saving change
sntp authentication-key
number md5 value
number:
(1..4294967295);
value: (1..8) characters.
By default,
authentication is
disabled
Specify authentication key for SNTP.
- number—key number
- value—key value
no sntp authentication-key
number
Delete authentication key for SNTP.
sntp authenticate
-/authentication is not
required
Enable mandatory authentication for getting information from
NTP servers.
no sntp authenticate
Restore the default value.
sntp trusted-key key_number
key_number:
(1..4294967295);
By default,
authentication is
disabled
Perform synchronization system authentication with SNTP by the
specified key.
- key_number—key number
no sntp trusted-key
key_number
Restore the default value.
sntp client poll timer seconds
seconds:
(60..86400)/1024
Set polling time for SNTP client.
no sntp client poll timer
Restore the default value.
sntp broadcast client enable
-/denied
Allow multicast SNTP client operation.
no sntp broadcast client
enable
Restore the default value.
sntp anycast client enable
-/denied
Allow the operation of SNTP clients that support packet
transmission to the nearest device in a group of receivers.
no sntp anycast client enable
Restore the default value.
sntp client enable
{gigabitethernet gi_port |
tengigabitethernet te_port |
port-channel group| vlan
vlan_id}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24);
vlan_id (1..4094)
/denied
Allow the operation of SNTP clients, that support packet
transmission to the nearest device in a group of receivers, and to
broadcast SNTP clients for the selected interface.
- for detailed interface configuration, see Interface Configuration
Section.