ELTEX MES3108 - Page 59

MES3000 Ethernet switch series 59
show interfaces status
-
Show status for all interfaces.
show interfaces status
{gigabitethernet gi_port |
tengigabitethernet te_port|
port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Show status for Ethernet port, port group.
show interfaces
{gigabitethernet gi_port |
tengigabitethernet te_port |
port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Show information about state, settings and statistics of Ethernet-
port, groups of ports
show interfaces advertise
-
Show autonegotiation parameters, announced for all interfaces.
show interfaces advertise
{gigabitethernet gi_port |
tengigabitethernet te_port |
port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Show autonegotiation parameters, announced for Ethernet port,
port group.
show interfaces description
-
Show descriptions for all interfaces.
show interfaces description
{gigabitethernet gi_port |
tengigabitethernet te_port |
port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Show descriptions for Ethernet port, port group.
show interfaces counters
-
Show statistics for all interfaces.
show interfaces counters
{gigabitethernet gi_port |
tengigabitethernet te_port |
port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Show statistics for Ethernet port.
show interfaces utilization
-
Show load statistics for all interfaces.
show interfaces utilization
[gigabitethernet gi_port |
tengigabitethernet te_port |
port-channel group]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Show load statistics for Ethernet port.
show interfaces mtu
[gigabitethernet gi_port |
tengigabitethernet te_port |
port-channel group]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Show MTU settings for the interface.
show ports jumbo-frame
-
Show jumbo frame settings for the switch.
show errdisable recovery
-
Show settings of the automatic port reactivation.
show errdisable interfaces
[gigabitethernet gi_port |
tengigabitethernet te_port |
port-channel group]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Show reasons for disabling the port, port group and the automatic
activation status.
Example execution of commands
 Show interface status:
console# show interfaces status
Flow Link Up Time Back Mdix
Port Type Duplex Speed Neg ctrl State (d,h:m:s) Pressure Mode Port Mode
-------- ------------ ------ ----- -------- ---- ----------- ----------- -------- ------- ---------
gi1/0/1 1G-Copper Full 1000 Enabled Off Up 01,00:54:25 Disabled Off Trunk
gi1/0/2 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/3 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/4 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/5 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/6 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/7 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/8 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/9 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/10 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/11 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/12 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/13 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/14 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/15 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/16 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/17 1G-Copper -- -- -- -- Down -- -- -- Access
gi1/0/18 1G-Copper -- -- -- -- Down -- -- -- Access