Endress+Hauser Proline Promass E 300

To Next Page

To Previous Page

Proline Promass E 300 PROFINET Operation options

Endress+Hauser 73

Source for device description files

See information →  74

Main Page

Table of Contents3
About this Document6
Document Function6
Symbols6
Safety Symbols6
Electrical Symbols6
Communication Symbols6
Tool Symbols7
Symbols for Certain Types of Information7
Symbols in Graphics7
Documentation8
Standard Documentation8
Supplementary Device-Dependent Documentation8
Registered Trademarks8
Safety Instructions10
Requirements for the Personnel10
Designated Use10
Workplace Safety11
Operational Safety11
Product Safety12
Security12
Device-Specific IT Security12
Protecting Access Via Hardware Write Protection12
Protecting Access Via a Password13
Access Via Web Server13
Access Via Service Interface (CDI-RJ45)14
Product Description15
Product Design15
Incoming Acceptance and Product16
Identification16
Incoming Acceptance16
Product Identification16
Transmitter Nameplate17
Sensor Nameplate18
Symbols on Measuring Device19
Storage and Transport20
Storage Conditions20
Transporting the Product20
Measuring Devices Without Lifting Lugs20
Measuring Devices with Lifting Lugs21
Transporting with a Fork Lift21
Packaging Disposal21
Installation22
Installation Conditions22
Mounting Position22
Environmental and Process Requirements24
Special Mounting Instructions26
Mounting the Measuring Device27
Required Tools27
Preparing the Measuring Device28
Mounting the Measuring Device28
Turning the Transmitter Housing28
Turning the Display Module29
Post-Installation Check29
Electrical Connection30
Connection Conditions30
Required Tools30
Requirements for Connecting Cable30
Terminal Assignment33
Device Plugs Available33
Pin Assignment of Device Plug33
Preparing the Measuring Device33
Connecting the Measuring Device34
Connecting the Transmitter34
Integrating the Transmitter into a Network38
Connecting the Remote Display and Operating Module DKX00140
Ensuring Potential Equalization40
Requirements40
Special Connection Instructions41
Connection Examples41
Hardware Settings44
Setting the Device Name44
Activating the Default IP Address46
Ensuring the Degree of Protection46
Post-Connection Check47
Operation Options48
Overview of Operation Options48
Structure and Function of the Operating Menu49
Structure of the Operating Menu49
Operating Philosophy50
Display51
Operational Display51
Navigation View52
Editing View54
Operating Elements56
Opening the Context Menu56
Navigating and Selecting from List58
Calling the Parameter Directly58
Calling up Help Text59
Changing the Parameters59
User Roles and Related Access Authorization60
Disabling Write Protection Via Access60
Code60
Enabling and Disabling the Keypad61
Access to the Operating Menu Via the Web Browser61
Function Range61
Prerequisites62
Establishing a Connection63
Logging on65
User Interface66
Disabling the Web Server67
Logging out67
Access to the Operating Menu Via the Operating Tool68
Connecting the Operating Tool68
Fieldcare71
Devicecare72
System Integration74
Overview of Device Description Files74
Current Version Data for the Device74
Operating Tools74
Device Master File (GSD)75
File Name of the Device Master File (GSD)75
Cyclic Data Transmission76
Overview of the Modules76
Description of the Modules76
Status Coding84
Factory Setting85
Startup Configuration86
System Redundancy S287
Commissioning88
Function Check88
Switching on the Measuring Device88
Connecting Via Fieldcare88
Setting the Operating Language88
Configuring the Measuring Device89
Defining the Tag Name90
Setting the System Units90
Displaying the Communication92
Interface95
Displaying the I/O Configuration95
Configuring the Current Input96
Configuring the Status Input97
Configuring the Current Output98
Configuring the Pulse/Frequency102
Switch Output102
10.5.10 Configuring the Relay Output111
10.5.11 Configuring the Local Display114
10.5.12 Configuring the Low Flow Cut off118
10.5.13 Configuring the Partial Filled Pipe119
Advanced Settings120
Using the Parameter to Enter the Access Code121
Calculated Values121
Carrying out a Sensor Adjustment122
Configuring the Totalizer123
Carrying out Additional Display Configurations125
WLAN Configuration129
Configuration Management131
Using Parameters for Device Administration133
Simulation134
Protecting Settings from Unauthorized Access137
Write Protection Via Access Code138
Write Protection Via Write Protection139
Switch139
Operation141
Reading the Device Locking Status141
Adjusting the Operating Language141
Configuring the Display141
Reading Measured Values141
Measured Variables" Submenu142
Totalizer143
Input Values" Submenu144
Output Values145
Adapting the Measuring Device to the Process147
Conditions147
Performing a Totalizer Reset147
Function Scope of the "Control Totalizer" Parameter148
Function Scope of the "Reset All Totalizers" Parameter148
Showing Data Logging148
Diagnostics and Troubleshooting152
General Troubleshooting152
Diagnostic Information Via Light Emitting154
Diodes154
Transmitter154
Diagnostic Information on Local Display156
Diagnostic Message156
Calling up Remedial Measures158
Diagnostic Information in the Web Browser158
12.4.1 Diagnostic Options158
Calling up Remedy Information159
12.5 Diagnostic Information in Fieldcare or159
Diagnostic Options159
Adapting the Diagnostic Information161
Adapting the Diagnostic Behavior161
Overview of Diagnostic Information164
Diagnostic of Sensor164
Diagnostic of Electronic171
Diagnostic of Configuration188
Diagnostic of Process201
Pending Diagnostic Events215
Diagnostic List215
12.10 Event Logbook216
12.10.1 Reading out the Event Logbook216
12.10.2 Filtering the Event Logbook217
12.10.3 Overview of Information Events217
12.11 Resetting the Measuring Device218
12.11.1 Function Scope of the "Device Reset" Parameter218
12.12 Device Information219
12.13 Firmware History221
Maintenance222
Maintenance Tasks222
Exterior Cleaning222
Interior Cleaning222
Measuring and Test Equipment222
Endress+Hauser Services222
Repair223
General Notes223
Repair and Conversion Concept223
Notes for Repair and Conversion223
Spare Parts223
Endress+Hauser Services223
Return223
Disposal224
Removing the Measuring Device224
Disposing of the Measuring Device224
Accessories225
Device-Specific Accessories225
For the Transmitter225
For the Sensor226
Communication-Specific Accessories226
Service-Specific Accessories227
System Components227
Technical Data228
Application228
Function and System Design228
Input229
Output232
Power Supply237
Performance Characteristics238
Installation242
Environment242
Process243
16.10 Mechanical Construction245
16.11 Human Interface248
16.12 Certificates and Approvals252
16.13 Application Packages255
16.14 Accessories256
16.15 Supplementary Documentation256
Index259

Endress+Hauser Proline Promass E 300 - Page 73

Table of Contents

Related product manuals