Endress+Hauser Proline Promass E TB2 HART - Page 4

Table of contents Proline Promass E TB2 HART
4 Endress+Hauser
10 Commissioning .................... 51
10.1 Function check ........................ 51
10.2 Switching on the measuring device ........... 51
10.3 Setting the operating language .............. 51
10.4 Configuring the measuring device ............ 52
10.4.1 Selecting and setting the medium ...... 53
10.4.2 Configuring the current outputs ........ 55
10.4.3 Configuring the local display .......... 59
10.4.4 Configuring the output conditioning ..... 61
10.4.5 Configuring the low flow cut off ....... 64
10.4.6 Configuring the partial filled pipe
detection ....................... 65
10.5 Advanced settings ....................... 66
10.5.1 Defining the tag name .............. 67
10.5.2 Setting the system units ............. 67
10.5.3 Carrying out a sensor adjustment ....... 69
10.5.4 Configuring the totalizer ............. 70
10.5.5 Carry out additional display
configurations .................... 71
10.6 Configuration management ................ 72
10.7 Simulation ............................ 73
10.8 Protecting settings from unauthorized access .... 74
10.8.1 Write protection via access code ....... 74
10.8.2 Write protection via lock switch ....... 75
11 Operation ......................... 77
11.1 Adjusting the operating language ............ 77
11.2 Configuring the display ................... 77
11.3 Reading off measured values ............... 77
11.4 Adapting the measuring device to the process
conditions ............................ 78
11.5 Perform totalizer reset .................... 78
11.6 Show data logging ...................... 79
12 Diagnostics and troubleshooting ..... 81
12.1 General troubleshooting .................. 81
12.2 Diagnostics event on local display ............ 82
12.2.1 Diagnostic message ................ 82
12.2.2 Calling up remedial measures ......... 83
12.3 Diagnostics event in the operating tool ........ 84
12.4 Diagnostic list ......................... 84
12.5 Overview of diagnostics events .............. 85
12.5.1 Adapting event level ............... 85
12.5.2 Diagnostics for the sensor ............ 85
12.5.3 Diagnostics for the electronics ......... 86
12.5.4 Diagnostics for the configuration ....... 87
12.5.5 Diagnostics for the process ........... 87
12.6 Event logbook ......................... 88
12.6.1 Event history .................... 88
12.6.2 Filtering the event logbook ........... 89
12.6.3 Overview of information events ........ 89
13 Repair ............................. 91
13.1 General notes .......................... 91
13.2 Spare parts ............................ 91
13.3 Endress+Hauser services .................. 92
14 Maintenance
...................... 93
14.1 Maintenance tasks ...................... 93
14.1.1 Exterior cleaning .................. 93
14.1.2 Interior cleaning .................. 93
14.2 Measuring and test equipment .............. 93
14.3 Endress+Hauser services .................. 93
15 Accessories ........................ 94
16 Return ............................ 95
17 Disposal ........................... 96
17.1 Removing the measuring device ............. 96
17.2 Disposing of the measuring device ........... 96
18 Technical data ..................... 97
18.1 Application ........................... 97
18.2 Function and system design ................ 97
18.3 Input ............................... 97
18.4 Output .............................. 98
18.5 Power supply .......................... 99
18.6 Performance characteristics ............... 100
18.7 Operating conditions: Installation ........... 102
18.8 Operating conditions: Environment .......... 102
18.9 Operating conditions: Process .............. 103
18.10 Mechanical construction ................. 105
18.11 Human interface ...................... 107
18.12 Certificates and approvals ................ 108
18.13 Application packages .................... 109
18.14 Accessories .......................... 109
Index ................................. 110