Enertech Global
EAV - EME/EMD Rev. A Models
Installaon and Operaons Manual
This heat pump provides heated and chilled soluon as well
as oponal domesc water heang capability. Engineering
and quality control is built into every unit. Good performance
depends on proper applicaon and correct installaon.
The signal words and
are used on product labels and throughout this manual to
idenfy levels of hazard seriousness.
Nocaon of installaon, operaon or maintenance
informaon which is important, but which is NOT hazard related.
Indicates a potenally hazardous situaon or an
unsafe pracce which, if not avoided, COULD result in minor or
moderate injury, product or property damage.
Indicates a potenally hazardous situaon which, if
not avoided, COULD result in death or serious injury.
Indicates an immediate hazardous situaon which, if
not avoided, WILL result in death or serious injury.
Used to highlight suggesons which will result in
enhanced installaon, reliability, or operaon.
Upon receipt of any equipment, carefully check the shipment
against the packing slip and the freight company bill of lading.
Verify that all units and packages have been received. Inspect
the packaging of each package and each unit for damages.
Ensure that the carrier makes proper notaon of all damages or
shortage on all bill of lading papers. Concealed damage should
be reported to the freight company within 5 days. If not led
within 5 days the freight company can deny all claims.
Nofy Enertech Global Customer Service Department
of all damages within 5 days. It is the responsibility of the
purchaser to le all necessary claims with the freight company.
Protect units from damage and contaminaon due to plastering
(spraying), painng and all other foreign materials that may be
used at the job site. Keep all units covered on the job site with
either the original packaging or equivalent protecve covering.
Cap or recap unit connecons and all piping unl the unit is
installed. Precauons must be taken to avoid physical damage
and contaminaon which may prevent proper start-up and may
result in costly equipment repair.
Units should be stored in an upright posion at all mes and
should not be stacked unless specially noted on the packaging.
Special care should be taken in locang the unit. Installaon
locaon chosen should include adequate service clearance
around the unit. The Indoor Module should be located in a
condioned space where the ambient temperature remains
between 55
o
F and 95
o
F with a maximum RH of 78-80%.
It should be located in a way that piping or other permanently
installed xtures do not have to be removed for servicing.
• Compare the electrical data on the unit nameplate with
packing slip and ordering informaon to verify that the
correct unit has been shipped.
• Inspect all electrical connecons and wires. Connecons
must be clean and ght at the terminals, and wires should
not touch any sharp edges or copper pipe.
• Verify that all refrigerant tubing is free of dents and kinks.
Refrigerant tubing should not be touching other unit
components.
• Before unit start-up, read all manuals and become familiar
with unit components and operaon. Thoroughly check the
unit before operang.
• Fill out the unit installaon form in the back of this IOM.
The dealer should instruct the consumer in the proper
operaon, maintenance, thermostat and indicator lights.
Also provide the consumer with the manufacturer’s Owner’s
Manual for the equipment being installed.
Enertech Global’s heat pumps and system installaons may
include electrical, refrigerant and/or water connecons. Federal,
state and local codes and regulaons apply to various aspects
of the installaon. Improperly installed equipment can lead
to equipment failure and health/safety concerns. For these
reasons, only qualied technicians should install an Enertech
Global built system.
Because of the importance of proper installaon, Enertech
Global does not sell equipment direct to homeowners. Internet
websites and HVAC outlets may allow for purchases directly by
homeowners and do-it-yourselfers, but Enertech Global oers
no warranty on equipment that is purchased via the internet or
installed by persons without proper training.
Enertech Global has set forth this policy to ensure installaons
of Enertech Global systems are done safely and properly. The
use of well-trained, qualied technicians helps ensure that your
system provides many years of comfort and savings.
⚠ ⚠
To Next Page
Loading...
