A1400 AIR 6 532129 04 - Rev.B
Translation of the original instructions
ENGLISH
12.11 J9 - XFA button photocells ...................................63
12.12 J7
- INPUTS E1 -E2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
............................................
63
12.13 J22 - Configurable outputs ..................................63
13. STARTUP ......................................................... 64
Preliminary checks prior to commissioning .................64
13.1 Switching on and system SETUP .............................64
Checks following SETUP .......................................64
Saving the Configuration ......................................64
13.2 Basic / advanced programming ..............................65
14. SYSTEM FUNCTIONALITY/CONFIGURATIONS ........... 73
14.1 Operating mode ................................................ 73
14.2 Inputs configuration ..........................................74
14.3 Configuration of J22 outputs .................................76
14.4 Obstacle detection .............................................76
14.5 Anti-intrusion and PULL&GO .................................76
14.6 ELASTIC Kit ......................................................76
14.7 Energy Saving Function ......................................76
Activating theEnergy Saving function .......................76
14.8FunctionLowEnergyduring
closing and OPENING ................................................77
Setting the Low Energy function during closing
CS CF ..77
Setting the Low Energy function during opening
OS OF 77
15. DIAGNOSTICS .................................................. 77
15.1 System diagnostics: alerts, errors .............................77
15.2 Troubleshooting ................................................81
16. OPERATIONS ON THE BOARD ............................... 82
16.1 Set-up ...........................................................82
How to perform setup from board ...........................82
16.2 RESET ............................................................82
When is Reset necessary .......................................82
How to perform a RESET from the board ....................82
16.3 Restoring factory status .......................................82
When is Restore necessary ....................................82
How to perform restore ........................................82
16.4 Updating (UPLOAD) ............................................83
16.5 Download .......................................................83
17. INTERCOM CANBUS
PROGRAMMING ONLY WITH SDKEVO 85
17.1 Intermode .......................................................86
17.2 Interlock .........................................................86
Interlock with no memory ....................................86
Interlock with memory ........................................87
18. LK EVO
FW VERSION 1.2 OR LATER
. . . . . . . . . . . . . . . . . . . . . . . .
........................
88
18.1 Assembly and testing ..........................................88
18.3 Special functions ...............................................89
19. KS EVO ........................................................... 90
19.1 Assembly and testing ..........................................90
20. SDK EVO
FW VERSION 3.0 OR LATER
. . . . . . . . . . . . . . . . . . . . . . .
.......................
93
20.1 Assembly and testing ..........................................93
20.2 Switching on and use ..........................................93
20.3 Home page .....................................................94
20.4 Reset - Lock/Release SDKEVO .................................94
20.5 PASSWORD ...................................................... 94
20.6 selection MENU ................................................95
20.7 Function MENU ................................................. 96
Menu 1 language ...............................................99
Menu 2 Programming ..........................................99
Menu 3 ERRORS ............................................... 103
Menu 4 INDICATIONS ......................................... 104
Menu 5 CYCLE COUNTER ..................................... 104
Menu 6 DATE / TIME .......................................... 104
Menu 7 TIMER ................................................. 105
Menu 8 PASSWORD ........................................... 106
Menu 9 INFO .................................................. 106
21. MAINTENANCE ................................................107
21.1 Calculation estimate of cycles performed ................. 107
Routine maintenance ........................................ 107
Periodic replacements ....................................... 107
21.2 Maintenance technician safety ............................. 108
21.3 Replacements ................................................ 108
21.4 Cleaning ....................................................... 110
21.5 Functional checks ............................................ 110
22. WASTE DISPOSAL .............................................110
23. ATTACHMENTS A1400 AIR ................................111
24. ATTACHMENTS A1400 AIR DM ............................112
24.1 Installation diagrams ........................................ 113
A1400 AIR H100 - H140 .......................................113
A1400 AIR with carriage leaf spacer .........................114
A1400 AIR H140 glass leaf ....................................115
24.2 Position of components on A1400 AIR support profile
.. 116
A1400 AIR Right Opening Single Leaf .......................116
A1400 AIR Left Opening Single Leaf ........................117
A1400 AIR Double Leaf .......................................118
24.3 Position of components on A1400 AIR DM support profile 119
A1400 AIR DM Right Opening Single Leaf ..................119
A1400 AIR DM Left Opening Single Leaf ................... 120
A1400 AIR DM Double Leaf .................................. 121
TABLES
1 Symbols: notes and warnings on the instructions .................... 8
2 Symbols: tools (type and size) ...................................... 8
3 Symbols: safety signs and symbols (EN ISO 7010) .................... 9
4 Symbols: markings on product ..................................... 9
5 Symbols: Personal Protective Equipment ............................ 9
6 Symbols: markings on packaging ................................... 9
7 Technical specifications .......................................... 12
8 Technical specifications .......................................... 13
9 Profile cutting measurements .................................... 20
10 Belt tensioning (measurements in mm) ........................... 45
11 Belt tensioning (measurements in mm) ........................... 46
12 LEDs on the board ............................................... 53
13 BASIC programming fw version 3.0 or later ........................ 66
14 ADVANCED programming fw version 3.0 or later ................... 69
15 Max. speed settings in Low Energy mode. ......................... 77
16 Status of the automation ........................................ 77
17 Errors ........................................................... 78
18 Warnings ....................................................... 79
19 AUX Errors ...................................................... 80
20 Troubleshooting guide ........................................... 81
21 Updating functions (UPLOAD) from USB ........................... 83
22 Download to USB functions ...................................... 83
23 Firmware and programming file names ........................... 83
24 BOOTLOADER Errors ............................................. 84
25 Errors .......................................................... 91
26 Warnings ....................................................... 92
27 Firmware Version ................................................ 92
28 FUNCTIONS Menu ............................................... 97
29 Maintenance programme and periodic replacements ............ 107
30 A1400 AIR Automation weights ................................ 111
31 Positions of components on the head section .................... 111
32 A1400 AIR DM automation weights ............................ 112
33 Positions of components on the head section .................... 112
To Next Page
Loading...
