FULTON Vantage VTG 2000 - Page 23

Questions? Please Contact Your Local Manufacturer’s Representative
SECTION 2 VTG-IOM-2016-1214 INSTALLATION
2-17
FIGURE 5  CONDENSATE DRAIN PIPING FOR VANTAGE BOILERS  SINGLE BOILER
REAR VIEW
DETAIL A
CONDENSATE
DRAIN KIT
DETAIL A
DRAWING NUMBER
REV
G-31-100002 A
CONDENSATE DRAIN PIPIN FOR SINGLE VANTAGE
BOILER
DESCRIPTION:
DRAWN BY:
M. BERWALD
CHECKED BY:
KDB
B.O.M. REVIEW
MECH. ENG:
SMT
ELEC. ENG:
APPROVED BY:
N/A
DGM
N/A
JOB NUMBER:
PROJECT NAME:
PROJECT MANAGER:
This design and
drawings are
proprietary and are the
exclusive property of
The Fulton Com panies.
The corporation does
not permit their use
except with prior
written consent.
The items shown in
this drawing may be
covered by one or
more patents of The
Fulton Companies.
1 OF 1
THIRD ANGLE PROJECTION
The Fulton Companies
972 Centerville Road
Pulaski, New York USA 13142
2/18/2014
3/3/2014
2/28/2014
3/3/2014
UNLESS OTHERWISE NOTED:
DIMENSIONS ARE IN INCHES
TOLERANCES ON
FRACTIONS
1/4
(2) PLACE DEC. .01
(3) PLACE DEC.
.005
ANGLES 2 DEG.
SURFACE FINISH
250 MICRO-INCHES
R
SHEET 1 OF 1
A
UPDATED CONNECTION FOR CONDENSATE
DRAIN. M.E.B. 9/10/14
N/A N/A
SMT
9/10/14
SMT
9/10/14
A.A.
9/11/14
REVISION HISTORY
REV REVISION DESCRIPTION B.O.M. ELEC. ENG MECH. ENG CHECKED APPROVED
REAR VIEW
DETAIL A
CONDENSATE
DRAIN KIT
DETAIL A
DRAWING NUMBER
REV
G-31-100002 A
CONDENSATE DRAIN PIPIN FOR SINGLE VANTAGE
BOILER
DESCRIPTION:
DRAWN BY:
M. BERWALD
CHECKED BY:
KDB
B.O.M. REVIEW
MECH. ENG:
SMT
ELEC. ENG:
APPROVED BY:
N/A
DGM
N/A
JOB NUMBER:
PROJECT NAME:
PROJECT MANAGER:
This design and
drawings are
proprietary and are the
exclusive property of
The Fulton Com panies.
The corporation does
not permit their use
except with prior
written consent.
The items shown in
this drawing may be
covered by one or
more patents of The
Fulton Companies.
1 OF 1
THIRD ANGLE PROJECTION
The Fulton Companies
972 Centerville Road
Pulaski, New York USA 13142
2/18/2014
3/3/2014
2/28/2014
3/3/2014
UNLESS OTHERWISE NOTED:
DIMENSIONS ARE IN INCHES
TOLERANCES ON
FRACTIONS
1/4
(2) PLACE DEC.
.01
(3) PLACE DEC.
.005
ANGLES
2 DEG.
SURFACE FINISH
250 MICRO-INCHES
R
SHEET 1 OF 1
A
UPDATED CONNECTION FOR CONDENSATE
DRAIN. M.E.B. 9/10/14
N/A N/A
SMT
9/10/14
SMT
9/10/14
A.A.
9/11/14
REVISION HISTORY
REV REVISION DESCRIPTION B.O.M. ELEC. ENG MECH. ENG CHECKED APPROVED
Figure 5 Notes:
 Header must be level or slightly pitched toward the drain.
 Header material to be galvanized steel or 316L stainless.
 0.75 inch (19 mm) condensate drain kit/trap outlet is
never to be above 1 inch boiler condensate outlet.
 The maximum capacity to attach, per condensate drain
kit, is 4 MMBH total.