FUTABA T18SZ - Telemetry: Altitude [Variometer]

102
＜ Linkagemenu ＞
Variometer
Asetupofthe
variometeronwhich
thealarmoperates.
↑ Anupwardarrow
indicatesthealarm
willsoundwhenthe
variometerreaches
aboveyoursetvalue.
↓ Adownwardarrow
indicatesthealarm
willsoundwhenthe
variometerreaches
belowyoursetvalue.
Alarmischosenfrom
Buzzer,Voice,and
Inhibit.
TheON/OFFswitch
ofSpeechischosen.
TheON/OFFswitch
ofmelodyischosen.
ŏ Tap the [Variometer] button in the Telemetry screen
to call the setup screen shown below.
Max.andmin.values
sincethepower
wasturnedONwill
display.
,WFDQQRWEHXVHGLQ)$667PRGHDQG6)+66PRGH
2QO\UHFHLYHUYROWDJHDQG(;7YROWDJHFDQEHXVHGLQ
)$667HVW&+PRGH
7KH)$667HVW&+7)+66PRGHFDQXVHDOOWKHWHOHPHWU\
IXQFWLRQV
Type1
Type2
Type3
"Vibrator"type
Ifthefollowingtypesareselected,thetransmitter
willvibrateduringthewarning.
First, the set of a reference is required.
1. The model and transmitter to which the
altitude sensor was connected are turned on.
2. Tap to the [Preset] of "Reference" item.
$WPRVSKHULFSUHVVXUHLVFKDQJHGDFFRUGLQJWRWKHZHDWKHU
DOVRDWWKHVDPHDLU¿HOG<RXVKRXOGSUHVHWEHIRUHDÀLJKW
*AnaltitudesensororGPSsensormustbeinstalledintheaircraft.
Telemetry:Altitude[Variometer]
Displaying data from the
variometer
9$5,2LVDVFUHHQZKLFKGLVSOD\VVHWVXSWKH
YDULRPHWHULQIRUPDWLRQIURPDQRSWLRQDODOWLWXGH
VHQVRURU*36VHQVRU
7KHYDULRPHWHURIWKHPRGHOZKLFKLVÀ\LQJFDQ
EHNQRZQ
,ILWEHFRPHVKLJKHURUORZHUWKDQWKHVHWWLQJDQ
DODUPDQGRUYLEUDWLRQZLOODOHUW\RX
7RHQVXUHWKDWWKHSLORWLVDZDUHDVWRWKHPRGHOV
VWDWXVWKH76=LQFRUSRUDWHVDGLIIHUHQWPHORG\
IRUDVFHQWDQGGHVFHQW$GGLWLRQDOO\GHSHQGLQJ
XSRQWKHUDWHRIFOLPERUGHVFHQWWKHWRQHVYDU\WR
LQGLFDWHZKHWKHURUQRWWKHDLUSODQHLVFOLPELQJRU
GHVFHQGLQJDWDUDSLGUDWH
Alert set : variometer
1. Tap Alarm and choose from Bu]]er, Voice,
and Inhibit.
2. When not operating vibrator, it is
"
Vibrator" to
Inhibit. Type1-3 will be chosen if it is made to
operate.
3. Tap to the Limit [m/s] item .
4. Adjust the rate by "ʈʈ" "ʈ" "ʆ" "ʆʆ" button.
Initial value: +1m
Adjustment range-50m/s~+50m/s
(ŃLimit
≧
ŅLimit)
:KHQWKHVFUHHQLVWDSSHGIRURQHVHFRQGWKHUDWHLVUHVHW
WRWKHLQLWLDOYDOXH
5. To terminate the input and return to the
original state, push the HOME/EXIT button.
● IfthisissettoMode1-4,
ariseanddivearetold
byadifferentmelody.
Mode1:Littlerise/dive
→ Melodychanges
:sensitively
Mode4:Bigrise/dive
→ Melodychanges
:insensible
ŏReturn to
Linkage menu