FUTABA T18SZ User Manual

142
＜ Modelmenu(Airplane/Glider/MulticopterFunctions) ＞
Trimmix1/2
[Corresponding model type]: Glider, general
These functions call the ailerons, elevators, and
ÀDSVFDPEHUÀDSVEUDNHÀDSVWULPRIIVHWUDWHV
SUHVHWDFFRUGLQJWRWKHÀLJKWVWDWH
The amount of ailerons, elevator, and flaps
FDPEHUÀDSEUDNHÀDSWULPRIIVHWFDQEHVHWWR
a switch.
As an example Trim mix 1 can be set up for
ODXQFKLQJZLWKVSHHGÀDSVDQGDLOHURQVGURSSHG
and a slight amount of up elevator. Trim mix
2 can be used for high speed flying, with both
DLOHURQVDQGVSHHGÀDSVUHÀH[HGVOLJKWO\DQGDELW
of down elevator.
The trim functions can be activated during
ÀLJKWE\VHWWLQJDVZLWFK7RSUHYHQWVXGGHQWULP
FKDQJHVZKHQVZLWFKLQJÀLJKWFRQGLWLRQVDGHOD\
can be set to provide a smooth transition between
the two. Trim mix 2 will have priority over Trim
mix 1.
Theailerons,flaps,andelevatorsoffsetratecanbeadjusted.
Taptothecorrespondingsettingitem.Adjusttherate.
Example
1. Move to the [INH] item
.
Set the trim mix function to
[ON].
*When separating the settings for each condition, move to
the [Group] item and set it to [Single].
2. Select the ON/OFF switch.
3. Select the [Manual] or [Auto] mode.
In the [Auto] mode, also select an auto SW. This
switch can be linked to a stick, etc.
<Speed>
In: The operation speed at switch ON can be set.
Out: The return speed at switch OFF can be set.
<Fine Tuning>
The offset rate can be varied in the Fine Tuning
numeric range set at screen by VR, etc. selection.
<Condition Delay>
When Áight conditions are set, the operation speed
can be set for each condition. Condition delay
operation can be interrupted and each rudder
Tuickly returned to its original position by selecting a
cut switch.
ŏ Select [Trim mix1 or 2] at the model
menu and call the setup screen
shown below.
Whenusingthis
function,Tap[INH].
(ONisdisplayed.)
TheON/OFFswitchof
mixingischosen.
Manual/Automode
selection
Manual:Switchesthe
functionON/OFFby
switch
Auto:Trimmixfunction
callcanbelinkedtoa
stick,etc.Astickswitch,
etc.separatefromthe
functionON/OFFswitch
isset.
Conditiondelaysetting
Conditiondelaycut
switch
Inspeed
Outspeed
（First）0〜27（Slowly）
*Thedisplayscreenisanexample.Theactual
screendependsontheModelType.
WhenafinetuningVR
isset,theaileronsflaps
andelevatorstrimrates
canbeadjusted.
Tonextpage
ŏReturn to Model menu
Thevalueinsidethe
parenthesesshowsthe
currentrudderposition.

FUTABA T18SZ Specifications

General

Channels	18
Frequency	2.4GHz
Telemetry	Yes
Modulation	FASSTest, FASST, S-FHSS, T-FHSS
Display	Color LCD
Model Memory	30