To Next PageTo Next Page
Need help?Do you have a question about the Gantner GAT Access 6100 Series and is the answer not in the manual?
General| Resolution | 800 x 480 pixels |
|---|---|
| Memory | 512 MB RAM |
| Operating System | Linux |
| Power Supply | 24 VDC |
| Protection Class | IP65 |
| Display | TFT |
| Processor | ARM Cortex-A8 |
| Flash Memory | 4 GB |
| RFID Reader | 13.56 MHz |
| Communication | Ethernet, RS-485, USB |
| User Interface | Touchscreen |
| Mounting Options | flush mounting |
Provides an overview of the manual's content and structure.
Summarizes the content of each chapter in the manual.
Identifies the intended audience and their roles for using this manual.
Explains text formatting conventions used for safety and important information.
Provides information on how to contact the manufacturer for questions.
Describes the specific applications and purposes of the GAT Access 6100 terminals.
Details the different models within the GAT Access 6100 series and their features.
Explains the normal procedure for using the GAT Access 6100 terminals.
Describes the various operational states the GAT Access 6100 terminals can be in.
Specifies the technical personnel responsible for installation procedures.
Covers general guidelines and considerations for mounting the GAT Access 6100 terminals.
Provides detailed steps and measurements for installing the GAT Access 6100.
Details the installation process specific to the GAT Access 6100 F PoE model.
Outlines the installation steps for the GAT Access 6100 F BIO terminal.
Explains how to set up the GAT Access 6100 F Enrollment Station.
Covers the installation procedures for the GAT TimeAxx 6150 terminal.
Describes the method for surface mounting the GAT TimeAxx 6150.
Details the process for flush mounting the GAT TimeAxx 6150.
Identifies personnel responsible for electrical connection tasks.
Explains how to connect power to the various GAT Access 6100 terminal types.
Specific power connection details for the Enrollment Station.
Power connection requirements for GAT Access 6100/F BIO / TimeAxx6150.
Details the power connection for the PoE model via Ethernet.
Guides on establishing network connectivity for the GAT Access 6100 terminals.
Network connection for most GAT Access 6100 series terminals via screw terminals.
Network connection for the PoE model via RJ45 socket.
Describes how to connect external devices via relay and optocoupler inputs.
I/O connections for standard terminals to turnstiles or doors.
I/O connections for the PoE model, including fingerprint reader option.
A checklist to verify all installation steps are completed before operation.
Identifies personnel responsible for commissioning and configuration tasks.
Explains the initial start-up and initialization process of the terminals.
Covers terminal settings that can be configured directly or via GAT Config Manager.
Details how to access and navigate the terminal's service menu for settings.
Explains how to configure network and communication settings like IP and DHCP.
Describes how to configure the RFID reader type and related functions.
Instructions for setting the correct date and time on the terminal.
How to adjust the contrast of the terminal's display for better readability.
Guide on how to reset the terminal system settings to their default values.
Overview of device functions configurable via GAT Config Manager.
Steps for configuring a GAT Access 6100 directly using the GAT Config Manager wizard.
How to set up projects in GAT Config Manager for device configuration.
A comprehensive list of all configurable settings for the GAT Access 6100.
How to edit and customize the text displayed on the terminal's screen.
Instructions for setting up the terminal for offline emergency operation.
Basic information on using the terminals with RFID data carriers.
Describes the different modes the GAT Access 6100 can operate in.
Explains the standard operating mode where the terminal communicates with a host.
Details the terminal's behavior when host communication is lost.
Describes the state when the terminal is unresponsive due to communication loss.
Identifies and explains the physical buttons, displays, and indicators on the terminals.
Step-by-step guide for users to gain access using a data carrier.
How users might need to provide additional input for access.
Troubleshooting tips for issues during data carrier write operations.
How users operate the terminal with fingerprint verification.
Instructions for using the Enrollment Station to record fingerprints.
Detailed steps for scanning and storing fingerprints at the enrollment station.
Guide on how to disable fingerprint verification for a data carrier.
Procedures to check the data carrier's access status and fingerprint quality.
Recommendations for cleaning the fingerprint sensor to ensure accurate readings.
Explains how the TimeAxx 6150 controls equipment with a countdown timer.
Compares online mode operation with emergency mode fallback.
Describes the display message when the terminal is out of order.
How to use the GAT Access 6100 for locker management functions.
How to set the terminal for continuous access without data carrier scanning.
How to activate external hardware like push buttons or turnstiles.
Instructions on using GAT Config Manager to update the terminal firmware.
Solution for updating the GAT Access 6100 firmware.
Guidance on configuring the GAT Access 6100 directly or via software.
Steps to enter the terminal's service mode for setting configuration.
Lists the communication ports used by the GAT Access 6100 for various functions.
Information on Ethernet bit rates and their configurability.
Methods for adjusting the terminal's date and time settings.
Procedures to locate and modify the terminal's IP address.
Methods for finding the terminal's MAC address.
Solutions for setting an IP address when the MAC is unknown or IP is 0.0.0.0.
Clarifies the "Time" vs "Delay" modes in Locker Check-In settings.
Explains the function of different optocoupler edge trigger settings.
Steps to authorize the LEGIC reader for data carrier interaction.
Methods for reading or clearing authorization data from LEGIC readers.
How to customize the text displayed on the terminal screen.
Addresses an issue where the relay activates despite host denial and suggests solutions.
Lists supported FUNLINE protocol commands for terminal communication.
Explains reasons for denied access in emergency mode based on site-key validation.
Provides specifications for the terminal's maximum start-up current consumption.
Lists the default configuration parameters for the GAT Access 6100 terminal.
Guide on configuring the terminal for offline emergency mode using an license.
Explains the function of data carrier certificates and their validation.
Specifies voltage requirements and power consumption for different terminal models.
Lists the supported RFID reader technologies and their specifications.
Details the host interface and terminal connection terminal specifications.
Technical specifications for the terminal's relay signal outputs.
Technical specifications for the terminal's optocoupler signal inputs.
Information on data storage and the internal clock functionality.
Lists the terminal's physical control elements and display types.
Technical details about the fingerprint reader's sensor and performance.
Information about the materials used for the terminal's housing.
Specifies the permitted operating and storage environmental conditions.
Provides physical dimensions for various GAT Access 6100 terminal models.
Physical dimensions for the GAT Access 6100 and GAT Access 6100 F PoE.
Physical dimensions for the GAT Access 6100 F PoE, including mounting plate.
Physical dimensions for the GAT Access 6100 F BIO terminal.
Physical dimensions for the GAT Access 6100 F Enrollment Station.
Physical dimensions for the GAT TimeAxx 6150 terminal.
