i-16 LOGIQ e – Basic Service Manual
5461614-100 English Rev. 6
Customer assistance
Contact information- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-33
Phone numbers for Customer Assistance - - - - - - - - - - - - - - - - - - - - - 1-34
System manufacturer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-34
Factory Site - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-35
Chapter 2 — Site Preparations
Overview
Contents in this chapter- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-2
General requirements
Contents in this Section- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-3
Ultrasound system environmental requirements- - - - - - - - - - - - - - - - - - 2-3
Electrical requirements - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-6
EMI limitations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-9
Probes environmental requirements - - - - - - - - - - - - - - - - - - - - - - - - - 2-11
Facility needs
Purchaser responsibilities - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-12
Required facility needs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-13
Desirable features- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-14
Suggested and Alternate Ultrasound Room Layout - - - - - - - - - - - - - - 2-15
Networking setup requirements - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-16
Environmental Dangers
Patient Environment IEC60601-1and ANSI AAMI ES60601-1 - - - - - - - 2-19
Chapter 3 — System Setup
Overview
Contents in this chapter- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-2
Setup reminders
Contents in this Section- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-3
Average setup time - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-3
Setup warnings- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-3
Receiving and unpacking the equipment
Contents in this Section- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-6
Receiving the LOGIQ e - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-6
Unpacking the LOGIQ e - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-7
Packing the Equipment - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-10
Preparing for setup
Verify customer order - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-11
Physical inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-11
EMI protection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-11
Completing the setup
Contents in this Section- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-12
System specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-12
Electrical specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-13
Power On / Boot Up - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-14
Power Off/Shutdown - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-16
Connecting probes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-17
System Configuration
Contents in this Section- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-19