Contents 3
Code no. 550038
Rev. no. 16/1018
4.7.1. CE certified models ................................................................................................................ 49
4.7.2. ETL certified models .............................................................................................................. 49
4.8. Exhaust ducting. Technical and connection details ......................................................................... 50
4.9. Wiring diagram ................................................................................................................................. 51
4.9.1. PB32, X13 models ................................................................................................................. 51
4.9.2. PB/PBP51, X20 models ......................................................................................................... 52
4.9.3. Symbols and measurements for the installation, positioning and connection ....................... 53
4.9.4. Height of the work stations ..................................................................................................... 54
5. INSTRUCTIONS FOR CONNECTING THE MACHINE ............................................................................... 55
5.1. Electrical requirements ..................................................................................................................... 55
5.1.1. Characteristics of the electrical wiring .................................................................................... 56
5.1.2. Connecting the machine to the mains power supply ............................................................. 56
5.2. Gas connection................................................................................................................................. 60
5.2.1. Installation characteristics ...................................................................................................... 61
5.2.2. Connecting the machine to the supply network ..................................................................... 61
5.3. Changing the type of gas ................................................................................................................. 62
5.3.1. CE certified models ................................................................................................................ 63
5.3.2. ETL certified models .............................................................................................................. 64
5.3.3. Atmospheric burner. Changing the type of gas ...................................................................... 65
5.3.4. Radiant burner. Changing the type of gas ............................................................................. 66
5.4. Steam connection ............................................................................................................................. 68
5.5. Connecting the exhaust ducting ....................................................................................................... 70
6. INITIAL START-UP OF THE MACHINE ...................................................................................................... 72
6.1. Initial checks ..................................................................................................................................... 72
6.2. Machines with gas heating. Gas pressure control ........................................................................... 73
6.2.1. CE models with atmospheric burner. Heating by natural gas, propane gas and propane-butane
mixture. ............................................................................................................................................. 73
6.2.2. ETL models with an atmospheric burner. Natural gas heating .............................................. 74
6.2.3. AGA models with an atmospheric burner .............................................................................. 75
6.2.4. CE models with radiant burner. Natural gas and propane gas heating ................................. 76
6.3. Machines with gas heating. Analysis of the combustion gases ....................................................... 77
6.3.1. Changing the position of the air extraction adjustment clapper valve .................................... 77
6.3.2. Adjusting the position of the Venturi ...................................................................................... 78
6.4. Machines with steam heating ........................................................................................................... 78
6.5. Machines with electric heating ......................................................................................................... 78
7. OPERATING AND USE. INTELI CONTROL. PB/PBP51, X20***W/F ........................................................ 79
7.1. Main menu. Intervention modes ....................................................................................................... 80
7.2. Control panel .................................................................................................................................... 81
7.3. Stop modes ...................................................................................................................................... 82
7.3.1. Normal machine stopping ...................................................................................................... 82
7.3.2. General Stop .......................................................................................................................... 82
7.3.3. Emergency stop devices ........................................................................................................ 82
7.4. Interpreting the main on-screen icons .............................................................................................. 84
7.5. Executing an ironing program .......................................................................................................... 85
7.5.1. Initiating an ironing program ................................................................................................... 85
7.5.2. Stopping the program ............................................................................................................. 86
7.5.3. SHUT DOWN mode ............................................................................................................... 86
7.5.4. Using the folder ...................................................................................................................... 87
7.5.5. Indicating preferable “OPTIFEED” ironing area ..................................................................... 88
7.5.6. Modifying a program in execution .......................................................................................... 91
7.5.7. Program modification screens................................................................................................ 92
7.6. Programming mode .......................................................................................................................... 93
7.6.1. Access to programming mode ............................................................................................... 93
7.6.2. Programming a new program ................................................................................................. 94
7.6.3. Folder ..................................................................................................................................... 96
7.6.4. Modifying existing programs ................................................................................................ 101
7.7. System tools mode ......................................................................................................................... 102
7.7.1. Configuration menu. Introduction and access ...................................................................... 102
7.7.2. Information menu. Introduction and access ......................................................................... 105
To Next Page
Loading...
Need help?
General
