CE6000-UM-251-9370 1-1
1 INTRODUCTION
1 INTRODUCTION
CAUTION
DOUBLE POLE/NEUTRAL FUSING
1.1 Main Speciîš¿cations
CE6000-40/60/120/120AMO
Item CE6000-40 CE6000-60 CE6000-120 (AMO)
CPU 32-bits CPU
Configuration Grit rolling
Drive system Digital servo
Maximum cutting area 375 mm x 50 m 603 mm x 50 m 1213 mm x 50 m
Guaranteed precision
cutting area
*1
356 mm x 2 m 584 mm x 5 m
(When using optional basket)
1194 mm x 5 m
(When using optional basket)
Mountable media width
*2
Minimum: 50 mm
Maximum: 484 mm
Minimum: 50 mm
Maximum: 712 mm
Minimum: 85 mm
(CE6000-120)
Minimum: 125 mm
(CE6000-120-AMO)
Maximum: 1346 mm
Available roll media
diameter
Minimum: 180 mm
Maximum: 76 mm
Maximum cutting speed 600 mm/s
(in all directions)
900 mm/s
(45° direction)
1000 mm/s
(45° direction)
Specifiable cutting speeds
(cm/s)
1–10, 15, 20, 25, 30, 35,
40, 45, 50, 55, 60 cm/s
1–10, 15, 20, 25, 30, 35,
40, 45, 50, 55, 60, 64
(45° direction 90 cm/s)
1–10, 15, 20, 25, 30, 35,
40, 45, 50, 55, 60, 71
(45° direction 100 cm/s)
Cutting Pressure 0.2 to 2.9 N
(20 gf to 300 gf) (31
steps)
0.2 to 4.4 N
(20 gf to 450 gf) (38 steps)
Minimum character size 5 mm (0.197 in) for alphanumeric Helvetica med. Font
Mechanical resolution 0.005 mm
Programmable resolution GP-GL: 0.1/0.05/0.025/0.01 mm; HP-GLTM
*3
: 0.025 mm
Repeatability accuracy
*1
Max. 0.1 mm/in unit of 2 m (Designated file and cutting condition)
No. of pens mountable 1 pen
Compatible cutter type Supersteel cutter blades
Compatible pen type Water-based fiber-tip pens and oil-based ballpoint pen
Compatible cutting film Marking film (PVC, fluorescent, or reflective film) up to 0.25 mm in thickness
(excluding high-luminosity reflective film)
Interfaces RS-232C/USB (Full Speed)
Buffer capacity 2 MB
Command modes GP-GL, HP-GL
*3
Display panel Liquid crystal graphic display (240dot x 128dot)
Rated power supply 100 to 120, 200 to 240 V AC, 50/60 Hz
Power consumption 100 VA
Operating environment 10°C to 35°C, 35% to 75% RH (Non-condensing)
Conditions for guaranteed
precision
16°C to 32°C, 35% to 70% RH (Non-condensing)
External dimensions
(W x D x H)
Approx.
672 x 336 x 266 mm
Approx.
901 x 593 x 1045 mm
Approx.
1541 x 736 x 1250 mm
Weight 10.5 kg 21 kg (Including stand) 40.5 kg (Including stand)
*1: Varies depending on the type of Graphtec-authorized îš¿lm and the cutting conditions
*2: The accuracy of minimum media width is when the push rollers are set to 5 mm from both edges of media.
*3: HP-GL
TM
is a registered trademark of Hewlett-Packard Company.
To Next Page
Loading...
