GW Instek GDM-8261A

To Next Page

To Previous Page

GDM-8261A User Manual

7. Then the default setting appears.

Example: DCV, Auto, 100mV range

SDC

AUTO

www. .com

information@itm.com1.800.561.8187

Main Page

Table of Contents3
Safety Instructions6
Safety Symbols6
Safety Guidelines7
Getting Started11
GDM-8261A Characteristics11
Characteristics GDM-8261A Characteristics11
Front Panel Overview12
Panel Overview Front Panel Overview12
Measurement Keys (Upper Row)13
Measurement Keys (Lower Row)16
Rear Panel Overview18
Set up20
Setup20
Tilt Stand20
Power up21
Basic Measurement23
Basic Measurement Overview25
Refresh Rate25
Reading Indicator26
AC/DC Voltage Measurement27
Manual/Automatic Triggering27
Select Voltage Range28
Voltage Conversion Table30
Crest Factor Table31
AC/DC Current Measurement32
Select Current Range33
2W/4W Resistance Measurement34
Select Resistance Range35
Diode Test37
Continuity Test38
Set Continuity Threshold39
Select Beeper Setting40
Frequency/Period Measurement41
Select Frequency/Period Voltage Range42
Temperature Measurement43
Temperature Temperature Measurement43
Select Thermocouple Type44
Set Reference Junction Temperature (T-CUP)45
Select Temperature Sensor Type46
Set User RTD47
Dual Measurement49
Advanced Measurement55
Advanced Measurement Overview56
Refresh Rate56
Reading Indicator57
Common Attribute: Manual/Automatic Triggering57
Dbm/Db/W Measurement58
Measure Dbm/W58
Measure Db59
Max/Min Measurement61
Relative Value Measurement62
Hold Measurement64
Compare Measurement65
Math Measurement68
Measure MX+B68
Measure 1/X70
Measure Percentage70
Statistics Calculations71
System/Display Configuration74
Refresh Rate Setting75
View Serial Number75
Trigger Setting76
Manual/Automatic Triggering76
Use External Trigger76
Set Trigger Delay78
Filter Setting79
Digital Filter Overview79
Digital Filter Setting80
Analog Filter Settings82
Display Setting83
Display Light Setting83
Measurement Configuration Settings84
D-Shift Settings84
Input Resistance Setting85
AC Bandwidth Setting86
Current Input Port Auto-Detect Setting87
ADC Setting88
Auto-Zeroing88
Auto-Gain90
ADC Speed Setting92
Frequency / Period Settings93
Input Port Selection93
Gate Time Setting95
Identification Settings96
Changing the Identification String96
Store/Recall97
Store Measurement Record98
Recall Measurement Record99
Save Instrument Settings100
Recall Instrument Settings101
Scanner (Optional)103
GDM-SC1 Scanner Specifications104
Scanner Installation104
Configure Scanner104
Select Channel Group and Enable Scanner106
Connect Wires107
Insert Scanner110
Scanner Configuration Record112
Setup Scan113
Overview113
Setup Simple Scan114
Setup Advanced Scan116
Use External Trigger119
Run Scan120
Run Overview120
Run Scan/Step120
Recall Scan/Step Result121
Setup and Run Monitoring121
Digital I/O123
Digital I/O Terminal Configuration124
Remote Control130
Configure Interface132
Overview132
Configure USB Interface132
Configure RS-232C Interface133
Set the EOL Character134
Set the Separation Character135
Set the Return Format136
Insert GPIB Card138
Configure GPIB Interface139
Insert Ethernet Card141
Activate Ethernet Interface142
Configure Ethernet Interface (RESET)144
Configure Ethernet Interface to DHCP145
Configure Ethernet IP146
View MAC Address152
Configure Telnet Port153
Return to Initial Settings154
View Web Password Settings156
Remote Terminal Session (Telnet)157
Web Control Interface159
Web Control160
Command Syntax163
Command Syntax Command Syntax163
Command Set164
Set Configure Commands173
Secondary Display: Configure2 Commands175
Measure Commands178
Sense Commands181
Faq210
Appendix212
Firmware Version213
Fuse Replacement214
Replace AC Source Fuse214
Replace Input Current Fuse215
Menu Tree216
Status System218
Specifications219
General219
DC Characteristics [3]220
AC Characteristics [1]222
Frequency and Period Characteristics225
Temperature Characteristics226
Dimensions227
EC Declaration of Conformity228

GW Instek GDM-8261A - Page 22

Table of Contents

Related product manuals