HEIDENHAIN TNC 370 - Page 330

%chwortverzerchnrs
0
Iptronal tnterruptron of a
program run .......................... .3-7
Orrented sprndle stop .................
8-69
>
4
Part program ............................
l-l 8
‘ath contours
Cartesran coordrnates ............. 5-9
Chamfer .......................... 5-l 2
Ctrcular path C around
circle center CC ................ 5-17
Circular path CR with defined
radrus .......................... 5-20
Circular path CT wrth tangentral
connection
Corner rounding RND
....... 5-23
......... 5-25
Straight line ..................... 5-9
Free contour programmrng .. ..5-3 6
Polar coordrnates ............... 5-27
Circular path CP around
pole CC ........................
5-30
Circular path CTP wrth
tangential connectron ........... 5-32
Stratght line LP ................. 5-27
Path functrons
......... ................. 5-2
General rnformatron
.............. 5-7
Overvrew ...................... 5-8
r’eckrng ...............................
8-6
Pitch crrcle ..............................
8-35
‘LC software number ............. 1 1-7
locket
Finrshrng ........................... .8-18
Mrllrng
............ ............. 8-17
olar coordrnates
General rnformatron ............ l-20
Polar Angle PA ..................... I-20
Polar Radrus PR .................... I-20
r’ole CC .........................
1-21, 5-27
Posrtron drsplay types ............... 1 1-6
7osrtion encoders ....................... I-25
‘osrttoning
wrth Manual Data Input ............ 5-57
Program ................ .................. I-36
Changrng ..................... ........ 4-3
Copying .............................. I-38
Directory ..............................
I-36
Edrtrng ............. ................... 4-2
Erasing
..................... ........... I-39
Layout ................................... .4-2
Management ......................... I-36
Protecting
.............................
I-37
Renaming ............................. 1-38
Selectrng
.............................
I-37
Size ..... .............................
I-36
Status ............ .................. I-36
Program run
Aborting ................ ................. 3-4
Interrupting
.............................
.3-4
Resumrng after an Interruptron ..3- 5
‘rogram section repeats ............... .6-5
Calling
.... ..................
........
6-5
P
Princrple ..................................... .6-5
Programming notes ....................
6-5
Programming ............................... l-l 8
Programming formats .................. 1 1-3
0
0 parameters
Checking ..................... ......... 7-1 1
Output ........................ 7-l 2, 7-1 3
Preassrgned ......................... 12-1 2
R
Rapid traverse .......................... .4-21
Readrng from system data .......... .7-14
Reaming ...................................... .8-8
Reference marks ......................... 1-25
Reference system ........................
l-l 9
Rotary axes .............................
I-20
Rotatron .................................... 8-65
Rough-out ................................. 8-42
RS-232-C Interface ..................... 1 1-5
Ruled surface ............................. 8-57
S
Scaling factor ..........
... .............. 8-66
Screen layout .................................
1-4
SL cycles ................................ .8-40
Contour geometry .................. .8-41
Contour milling
....................... 8-51
Overlapping contours ............. .8-44
Pilot drrllrng .............................. 8-50
Rough-out ...............................
8-42
Scheme ................................ 8-52
Slot
with recrprocating plunge-cut ... 8-28
Slot milling ...................................
.8-27
Slot mrllrng with reciprocating plunge-
cut
..................................... .8-28
Soft key structure .......................... 1-7
Spindle speed
Changing ...........
..................... 4-22
Status display .............................
1-31
AddItIonal ............ .................... I-31
STOP function ............................. .4-23
Stud finishing ............................... .8-20
Subprograms ............................... .6-2
Callrng
....................................
..6- 3
Operating lrmits ...................... 6-2
Principle .............
.................. 6-2
Switch-on ................ .............. 1-26
T
Tangenttal connectron of a contour
element .............................
5-23
Tapping ............ ...................... 5-35
Rrgrd tapping ........................
.8-l 3
with a floating tap holder ......... .8-12
T
Technical information ................. 12-14
Test run
Executing ................................... .3-2
Interrupting ............................... 3-2
TNC 370 ......................................... I-2
Accessorres ................ l-l 7, 12-16
Error messages .................... 12-l 7
Graphics ................................. I-27
Operating panel ...................... 1-3
Screen layout ............................. 1-4
Soft key structure ....................... 1-7
FK Programming
................. I-13
HANDWHEEL .................... l-8
HELP function ...................... l-l 6
MOD function ....................... l-l 6
Program Run .......................... 1-9
Programmrng and Editing .... l-l 0
Tool
Compensation values .............. .4-l 5
Data ........................................... .4-5
Calling ................................. .4-l 3
Delta values ......................... .4-6
Entering
... .............................. 4-7
Length L .................................. .4-5
Number ..................................... 4-5
Pocket table ........................... ..4- 12
Position ................................ .,.4-l 4
Radius R .................................... ,4-5
Table ................................. 4-9
Tool change ............................ 4-1 4
Automatic .............................. 4-l 4
Manual .................................. 4-14
Tool changer ............................ 4-1 2
Tools
Measuring tools automatrcally .9-31
Touch probe functions ............ .9-4
Touch probe system
Calibration ................................ 9-5
Length .................................. 9-5
Radius .............................. 9-6
Measuring with the ........... .9-l 4
Trigonometric functions ................ 7-8
U
Unit of measure ............................ 1 1-3
User parameters ............... 11-2, 12-2
w
Words
Editing .................................. 4-4
Finding ....................................
4-3
Inserting .................................. 4-4
Selecting .................................. .4-3
Workpiece .................................... I-23
Compensating misalignment ... ..9- 7
Positions ................................... I-23
Absolute ............................... I-23
Incremental ......................... I-23
TNC 426