HOEFLON C10 - Page 72

72 User Manual Compact Crane C10
E064
Not used.
E065
Not used.
E066
Problem with connection.
Switch machine off and on again.
E067
Problem with connection.
Switch machine off and on again.
E068
Not used.
E069
Not used.
E070
Problem with connection.
Switch
machine off and on again.
E071
Problem with connection.
Switch machine off and on again.
E072
Not used.
E073
Not used.
E074
Problem with connection.
Switch machine off and on again.
E075
Problem with connection.
Switch machine off and on
again.
E076
Not used.
E077
Not used.
E078
No contact with left
-
front angle sensor.
Switch machine off and on again.
E079
Incorrect value left
-
front angle sensor.
Switch machine off and on again.
E080
Incorrect value left
-
front angle sensor.
Switch machine off and on again.
E081
Problem left front.
Contact Hoeflon or your dealer.
E082
Problem left
-
front length sensor.
Activate the bypass and extend farther. The fault code disappears. Switch the
bypass off.
E083
Problem left
-
front
length sensor.
Activate the bypass and extend farther. The fault code disappears. Switch the
bypass off.
E084
Not used.
E085
No contact with right
-
front angle sensor.
Switch machine off and on again.
E086
Incorrect value right
-
front angle
sensor.
Switch machine off and on again.
E087
Incorrect value right
-
front angle sensor.
Switch machine off and on again.
E088
Problem right front.
Contact Hoeflon or your dealer.
E089
Problem right
-
front length sensor.
Activate the bypass and
extend farther. The fault code disappears. Switch the
bypass off.
E090
Problem right
-
front length sensor.
Activate the bypass and extend farther. The fault code disappears. Switch the
bypass off.
E091
Not used.
E092
No contact with right
-
rear
angle sensor.
Switch machine off and on again.
E093
Incorrect value right
-
rear angle sensor.
Switch machine off and on again.
E094
Incorrect value right
-
rear angle sensor.
Switch machine off and on again.
E095
Problem right front.
Contact Hoeflon or
your dealer.
E096
Problem length sensor right rear.
Activate the bypass and extend farther. The fault code disappears. Switch the
bypass off.
E097
Problem length sensor right rear.
Activate the bypass and extend farther. The fault code disappears. Switch
the
bypass off.
E098
Not used.
E099
No contact with left
-
rear angle sensor.
Switch machine off and on again.
E100
Incorrect value left
-
rear angle sensor.
Switch machine off and on again.
E101
Incorrect value left
-
rear angle sensor.
Switch
machine off and on again.
E102
Problem right front.
Contact Hoeflon or your dealer.
E103
Problem left
-
rear length sensor.
Activate the bypass and extend farther. The fault code disappears. Switch the
bypass off.
E104
Problem left
-
rear length
sensor.
Activate the bypass and extend farther. The fault code disappears. Switch the
bypass off.
E105
Not used.
E106
No contact with jib angle sensor.
Switch machine off and on again.
E107
Incorrect value jib angle sensor.
Switch machine off and on
again.
E108
Incorrect value jib length sensor.
Activate the bypass and extend farther. The fault code disappears. Switch the
bypass off.
E109
Not used.
E110
No contact with boom angle sensor.
Switch machine off and on again.
E111
Incorrect value
boom angle sensor.
Switch machine off and on again.
E112
Not used.
E113
No contact with pressure sensor boom lift
cylinder.
Switch machine off and on again.
E114
No contact with pressure sensor boom lift
cylinder.
Switch machine off and on again.
E115
Not used.
E116
No contact with housing angle sensor.
Switch machine off and on again.
Fault code
Problem
Possible solution. If this does not work, contact Hoeflon.
E117
Incorrect value housing angle sensor.
Switch machine off and on again.
E118
Incorrect value housing dummy sensor.
Check placement of dummy.
E119
Not used.