iManager NetEco 6000
Device Installation and Commissioning Guide
Copyright © Huawei Technologies Co., Ltd.
6.3.3.1 Setting Monitoring Parameters for the Smart Cooling Product...............................................................................157
6.3.3.2 Creating an Smart Cooling Product on the NetEco ..................................................................................................159
6.3.4 Adding a UPS .................................................................................................................................................................162
6.3.4.1 Setting Monitoring Parameters for a UPS2000-G (over SNMP) ............................................................................162
6.3.4.2 Setting UPS5000 Monitoring Parameters (over SNMP) .........................................................................................164
6.3.4.3 Setting UPS5000 Monitoring Parameters (over Modbus TCP) ..............................................................................166
6.3.4.4 Creating a UPS on the NetEco...................................................................................................................................168
6.3.5 Adding a PDU ................................................................................................................................................................172
6.3.5.1 Setting Monitoring Parameters for a PDU8000 (over SNMP) ................................................................................172
6.3.5.2 Creating a PDU on the NetEco ..................................................................................................................................173
6.3.6 Adding a Power Module ................................................................................................................................................175
6.3.6.1 Setting Monitoring Parameters for TP483000D .......................................................................................................175
6.3.6.2 Creating a Power Module on the NetEco..................................................................................................................176
6.3.7 Adding a RPDU .............................................................................................................................................................178
6.3.7.1 Setting RPDU_HUAWEI_PDU2000-32-1PH-20-4-M2 Monitoring Parameters ..................................................178
6.3.7.2 Creating a RPDU on the NetEco ...............................................................................................................................179
6.4 Scenarios for Connecting the ECC500 Collector ...........................................................................................................182
6.4.1 Commissioning the ECC500 V6 Collector ..................................................................................................................182
6.4.1.1 Setting ECC500 V6 Collector IP Address.................................................................................................................182
6.4.1.2 Setting Pass-through Parameters for the ECC500 V6 Collector .............................................................................184
6.4.1.3 Setting SNMP Parameters for the ECC500 V6 Collector ........................................................................................185
6.4.1.4 Setting RS485 Parameters for the ECC500 V6 Collector........................................................................................188
6.4.1.5 Creating an ECC500 V6 Collector on the NetEco ...................................................................................................190
6.4.2 Adding Sensors ..............................................................................................................................................................192
6.4.2.1 Adding Dry Contact Interface Devices .....................................................................................................................192
6.4.2.1.1 Setting Door Status Sensor Monitoring Parameters on the ECC .........................................................................192
6.4.2.1.2 Setting Smoke Sensor and Water Leakage Sensor Parameters on the ECC ........................................................194
6.4.2.1.3 Setting Device Monitoring Parameters of an NO/NC Dry Contact on the ECC.................................................195
6.4.2.1.4 Creating an Icon for a Door Status Sensor on the NetEco ....................................................................................197
6.4.2.1.5 Creating the Water Sensor on the NetEco ..............................................................................................................200
6.4.2.1.6 Modifying Alarm Names for Dry Contacts on the NetEco ..................................................................................203
6.4.2.1.7 Modifying Performance Counters for Dry Contacts on the NetEco ....................................................................207
6.4.2.2 Adding Temperature Sensors .....................................................................................................................................208
6.4.2.2.1 Setting Temperature Sensor Monitoring Parameters.............................................................................................208
6.4.2.2.2 Setting Device IP Addresses of Temperature Sensors...........................................................................................210
6.4.2.2.3 Creating a Temperature Sensor on the NetEco ...................................................................................................... 211
6.4.2.2.4 Viewing a Temperature Map on the NetEco ..........................................................................................................213
6.4.2.3 Adding an Ambient Temperature and Humidity Sensor ..........................................................................................214
6.4.2.3.1 Setting Monitoring Parameters for an Ambient Temperature and Humidity Sensor ..........................................214
6.4.2.3.2 Creating a Temperature and Humidity Sensor on the NetEco ..............................................................................215
6.4.2.4 Adding a Water Leakage Sensor ................................................................................................................................217
6.4.2.4.1 Creating a Water Leakage Sensor on the NetEco ..................................................................................................217
To Next Page
Loading...
