l Run the gpon alarm-profile add command to configure a GPON alarm profile, which
is used for monitoring the performance of an activated ONU line.
Step 2 Add an ONU.
Connect two ONUs to GPON port 0/1/0. Set the ONU IDs to 1 and 2, SNs to
32303131D659FD40 and 6877687714852901, passwords to 0100000001 and 0100000002,
discovery mode for password authentication to once-on, and management mode to OMCI. Bind
the two ONUs to ONU line profile ftto_line and ONU service profile ftto_ser.
There are two methods of adding an ONU: add an ONU offline and confirm an automatically
discovered ONU.
l Add ONUs offline.
If the password of an ONU is known, run the ont add command to add an ONU offline.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#ont add 0 1 password-auth 0100000001 once-on no-aging
omci ont-lineprofile-name
ftto_line ont-srvprofile-name ftto_ser
huawei(config-if-gpon-0/1)#ont add 0 2 password-auth 0100000002 once-on no-aging
omci ont-lineprofile-name
ftto_line ont-srvprofile-name ftto_ser
l Confirm automatically discovered ONUs
If the password or SN of an ONU is unknown, run the port portid ont-auto-find command
in GPON mode to enable the ONU auto-discovery function of the GPON port. Then, run the
ont confirm command to confirm the ONU.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#port 0 ont-auto-find enable
huawei(config-if-gpon-0/1)#display ont autofind 0
//After this command is executed, the information about all ONUs connected to
the GPON port through optical splitters is displayed.
huawei(config-if-gpon-0/1)#ont confirm 0 ontid 1 sn-auth 32303131D659FD40 omci
ont-lineprofile-name
ftto_line ont-srvprofile-name ftto_ser
huawei(config-if-gpon-0/1)#ont confirm 0 ontid 2 sn-auth 6877687714852901 omci
ont-lineprofile-name
ftto_line ont-srvprofile-name ftto_ser
NOTE
If multiple ONUs of the same type bound to the same line profile or service profile are connected to the
same port, you can bulk add ONUs by bulk confirming automatically discovered ONUs to make
configuration easier and more efficient. To do so, the preceding command can be modified as follows:
huawei(config-if-gpon-0/1)#ont confirm 0 all sn-auth omci ont-lineprofile-name
ftto_line
ont-srvprofile-name ftto_ser
l (Optional) Bind the alarm profile to the ONU.
The default profile 1 is used in this example.
huawei(config-if-gpon-0/1)#ont alarm-profile 0 1 profile-id 1
huawei(config-if-gpon-0/1)#ont alarm-profile 0 2 profile-id 1
Step 3 Check ONU status.
After an ONU is added, run the display ont info command to query the current status of the
ONU. Ensure that Config flag of the ONU is active, Run State is online, Config state is
normal, and Match state is match.
huawei(config-if-gpon-0/1)#display ont info 0 1
---------------------------------------------------------------------
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
12 FTTO Configuration(SOHO and SME)
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1102
To Next Page
Loading...
Need help?
General
