Step 5 Configure the inband management VLAN and IP address of the ONU.
huawei(config)#interface gpon 0/2
huawei(config-if-gpon-0/2)#ont ipconfig 1 1 static ip-address 192.168.50.2 mask
255.255.255.0 gateway
192.168.50.1 vlan 8
huawei(config-if-gpon-0/2)#quit
Step 6 Configure an inband management service port.
huawei(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 11 multi-service
user-vlan 8 rx-cttr 6 tx-cttr 6
Step 7 Confirm that the management channel between the OLT and the ONU is available.
l On the OLT, run the ping 192.168.50.2 command to check the connectivity between the
OLT and the ONU. The ICMP ECHO-REPLY packet from the ONU should be received.
l On the OLT, you can remote log in to the ONU to perform the configuration.
Step 8 Configure a channel for the Internet access service.
huawei(config)#vlan 100 smart
huawei(config)#vlan attrib 100 stacking
huawei(config)#port vlan 100 0/19 0
huawei(config)#service-port vlan 100 gpon 0/2/1 ont 1 gemport 12 multi-service
user-vlan 1001 tag-transform translate-and-add rx-cttr 6 tx-cttr 6
Step 9 Configure a channel for the Voice service.
huawei(config)#vlan 200 smart
huawei(config)#port vlan 200 0/19 0
huawei(config)#traffic table ip index 9 cir off priority 5 priority-policy local-
setting
huawei(config)#service-port vlan 200 gpon 0/2/1 ont 1 gemport 13 multi-service
user-vlan 200 rx-cttr 9 tx-cttr 9
Step 10 Configure a channel for the VoD service.
huawei(config)#vlan 300 smart
huawei(config)#port vlan 300 0/19 0
huawei(config)#traffic table ip index 10 cir off priority 4 priority-policy local-
Setting
huawei(config)#service-port vlan 300 gpon 0/2/1 ont 1 gemport 14 multi-service
user-vlan 300 rx-cttr 10 tx-cttr 10
Step 11 Configure a channel for the multicast service.
huawei(config)#vlan 1000 smart
huawei(config)#port vlan 1000 0/19 0
huawei(config)#service-port vlan 1000 gpon 0/2/1 ont 1 gemport 14 multi-service
user-vlan 1000 rx-cttr 10 tx-cttr 10
huawei(config)#btv
huawei(config-btv)#igmp cascade-port 0/2/1 ontid 1 gemport-index 14
huawei(config)#multicast-vlan 1000
huawei(config-mvlan1000)#igmp ipv6 version v2
huawei(config-mvlan1000)#igmp ipv6 mode proxy
Are you sure to change IGMP IPv6 mode?(y/n)[n]:y
huawei(config-mvlan1000)#igmp uplink-port 0/19/0
huawei(config-mvlan1000)#igmp program add batch ipv6 ff15:: to-ipv6 ff15::ffff
source-ipv6 2000::1
Step 12 Configure LAG for upstream ports.
Configure upstream ports 0/19/0 and 0/19/1 into an aggregation group. Each member port in the
aggregation group allocates packets based on the source MAC address. The working mode is
LACP static aggregation.
huawei(config)#link-aggregation 0/19 0-1 ingress workmode lacp-static
Step 13 (Optional) When PPPoE is adopted, enable forwarding the packets with PITP tag on the OLT
equipment.
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
19 IPv6 Configuration
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1912
To Next Page
Loading...
Need help?
General
