EasyManuals Logo
Home>IBM>Server>P 615 series

IBM P 615 series User Manual

IBM P 615 series
491 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #90 background imageLoading...
Page #90 background image
v
2,
4,
5,
and
7
There
is
no
requirement
that
memory
DIMM
slots
1,
3,
6,
and
8
be
populated
before
memory
DIMM
slots
2,
4,
5,
and
7.
Attention:
Go
to
the
service
processor
menus.
In
the
System
Information
Menu,
select
Memory
Configuration/
Deconfiguration.
Verify
on
the
first
screen
that
memory
repeat
gard
is
disabled.
If
it
is
enabled,
disable
it
for
the
duration
of
this
MAP.
When
exiting
this
MAP
to
go
to
MAP
0410
in
the
RS/6000
Eserver
pSeries
Diagnostic
Information
for
Multiple
Bus
Systems,
return
the
setting
to
enabled
if
necessary.
Step
1240-1
1.
Turn
off
the
power.
Remove
the
power
cord.
2.
Reseat
the
DIMMs.
3.
Reattach
the
power
cord.
Wait
for
OK
in
the
operator
panel.
4.
Turn
on
the
power.
Attempt
to
boot
to
the
SMS
menus.
(The
system
may
stop
with
an
8-digit
error
code
before
it
reaches
the
SMS
menus.)
5.
Power
down
the
system
using
the
white
button.
After
the
OK
appears
in
the
operator
panel,
look
at
the
memory
configuration/deconfiguration
menu.
Are
any
DIMMs
deconfigured
or
does
the
error
code
recorded
in
“Step
1240-1”
still
appear?
NO
Reseating
the
DIMMs
has
corrected
the
problem.
Enable
memory
repeat
gard
if
necessary.
Go
to
″MAP
0410:
Repair
Checkout″
in
the
RS/6000
Eserver
pSeries
Diagnostic
Information
for
Multiple
Bus
Systems.
YES
If
there
is
only
one
quad
of
DIMMs
on
the
planar,
go
to
“Step
1240-5”
on
page
71.
If
there
are
two
quads
of
DIMMs
on
the
planar,
go
to
“Step
1240-2.”
Step
1240-2
1.
Turn
off
the
power.
Remove
the
power
cord.
2.
Remove
one
quad
of
DIMMs.
Record
the
positions
of
the
DIMMs
as
they
are
removed.
When
instructed
to
reinstall
the
DIMMs,
install
them
back
into
the
same
slots
from
which
they
were
removed.
3.
Reattach
the
power
cord.
Wait
for
OK
in
the
operator
panel.
4.
Turn
on
the
power.
Attempt
to
boot
to
the
SMS
menus.
(The
system
may
stop
with
an
8-digit
error
code
before
it
reaches
the
SMS
menus.)
5.
Power
down
the
system
using
the
white
button.
After
the
OK
appears
in
the
operator
panel,
look
at
the
memory
configuration/deconfiguration
menu.
Are
any
DIMMs
deconfigured
or
does
the
error
code
recorded
in
“Step
1240-1”
still
appear?
NO
Go
to
“Step
1240-3”
on
page
71.
YES
Go
to
“Step
1240-5”
on
page
71.
70
EserverpSeries
615
Service
Guide

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the IBM P 615 series and is the answer not in the manual?

IBM P 615 series Specifications

General IconGeneral
BrandIBM
ModelP 615 series
CategoryServer
LanguageEnglish

Related product manuals