EasyManuals Logo

IBM P 615 series User Manual

IBM P 615 series
491 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #91 background imageLoading...
Page #91 background image
Step
1240-3
1.
Turn
off
the
power.
Remove
the
power
cord.
2.
Move
the
quad
of
DIMMs
located
on
the
card
to
the
other
quad’s
slots.
3.
Reattach
the
power
cord.
Wait
for
OK
in
the
operator
panel.
4.
Turn
on
the
power.
Attempt
to
boot
to
the
SMS
menus.
(The
system
may
stop
with
an
8-digit
error
code
before
it
reaches
the
SMS
menus.)
5.
Power
down
the
system
using
the
white
button.
After
the
OK
appears
in
the
operator
panel,
look
at
the
memory
configuration/deconfiguration
menu.
Are
any
DIMMs
deconfigured
or
does
the
error
code
recorded
in
“Step
1240-1”
on
page
70
still
appear?
NO
Go
to
“Step
1240-4.”
YES
Replace
the
system
planar.
Enable
memory
repeat
gard
if
necessary.
Go
to
″MAP
0410:
Repair
Checkout″
in
the
RS/6000
Eserver
pSeries
Diagnostic
Information
for
Multiple
Bus
Systems.
Step
1240-4
The
failing
DIMM(s)
is
in
the
quad
of
DIMMs
that
was
removed
in
“Step
1240-2”
on
page
70.
Do
the
following:
1.
Turn
off
the
power.
Remove
the
power
cord.
2.
Remove
the
quad
of
DIMMs
that
is
on
the
system
planar
and
reinstall
the
quad
of
DIMMs
that
had
been
removed.
The
DIMMs
can
be
reinstalled
in
either
quad.
3.
Go
to
“Step
1240-6”
on
page
72.
Step
1240-5
1.
Turn
off
the
power.
Remove
the
power
cord.
2.
Move
the
quad
of
DIMMs
that
is
on
the
system
planar
to
the
other
quad’s
location.
3.
Reattach
the
power
cord.
Wait
for
OK
in
the
operator
panel.
4.
Turn
on
the
power.
Attempt
to
boot
to
the
SMS
menus.
(The
system
may
stop
with
an
8-digit
error
code
before
it
reaches
the
SMS
menus.)
5.
Power
down
the
system
using
the
white
button.
After
the
OK
appears
in
the
operator
panel,
look
at
the
memory
configuration/deconfiguration
menu.
Are
any
DIMMs
deconfigured
or
does
the
error
code
recorded
in
“Step
1240-1”
on
page
70
still
appear?
NO
Replace
the
system
planar.
Enable
memory
repeat
gard
if
necessary.
Go
to
″MAP
0410:
Repair
Checkout″
in
the
RS/6000
Eserver
pSeries
Diagnostic
Information
for
Multiple
Bus
Systems.
YES
One
or
more
of
the
DIMMs
on
the
card
is
defective.
Go
to
“Step
1240-6”
on
page
72.
Chapter
3.
Maintenance
Analysis
Procedures
(MAPs)
71

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the IBM P 615 series and is the answer not in the manual?

IBM P 615 series Specifications

General IconGeneral
BrandIBM
ModelP 615 series
CategoryServer
LanguageEnglish

Related product manuals