infin ite
TM
DVX
Plus
Digital Systems Quick Reference Card
FIXED FEATURE BUTT ONS
• CA MP - ON Button -- Enables you to alert a busy
party that an outside line is on hold and waiting
for them.
• CONF (CONFERENCE) Button -- Used to
establish and build conference calls.
• FLASH Button -- Used to terminate an outside
call and restore dial tone without having to
hang up the handset. It is also used to transfer
calls behind a PBX or Centrex within those
sys tems.
• FORWARD (FWD) Button -- Allows you to
forward your calls to another station.
• HOLD Button -- Enables you to place an outside
caller on hold.
• H- T- P Switch -- Allows the user to select the ICM
signaling mode: Handsfree, Tone, or Privacy.
• MSG (MESSAGE WAIT) Bu tton -- Allows you to
initiate a message waiting indication at stations
that are busy, unattended, or in Do Not Disturb.
Message Waiting Callback request left at your
station is indicated by a flashing MSG WAIT LED.
• MUTE Button -- Allows you to switch the built-
in micro pho ne on or of f wh en us in g th e
speakerphone, or the handset microphone
when u sing the hands et.
• ON/OFF Button -- Enables you to make a
telephone call without lifting the handset. It
turns the telephone on and off when using the
speakerphone.
• SPEED Button -- Provides you with access to
speed dialing, save number redial and last
number redial. This button is also used to
access flexible button programming.
• TRANS (T RA NSF ER) Button -- Used to transfer
an outside call from one station to another.
• VOLUME BAR -- Allows the user to adjust
speakerphone and handset volume.
CALL FORWARDING
1. Pres s the FWD butto n or dial [6 40].
2. Dial the des ired Call Fo rward co de:
[6] = All Calls
[7] = No Answer
[8] = Busy
[9] = Busy/No Answer
3. Dial station number where calls are to be
forwarded. Hear confirmation tone.
4. Replac e h and set o r press ON/OFF bu tt on .
ESTABLISHING A CON FERENCE
Only stations that have Conference enabled will be
able to initiate a Conference.
1. Lif t the handset.
2. Selec t int ercom station or dial desir ed o ut side
party. When called party answers, press the
CO NF bu tt on .
3. Ad d next conf eren ce party by s electing
another outside line or intercom station.
4. Press the CONF button again and repeat
previous step in a cycle, until all parties are
co nt act ed.
5. When last party answers , press the CONF
button twice. All parties are connected.
TERMINATI NG A CONFE RE NCE
To termin ate a Conference, the conference in itiato r
must be actively in the conference.
R eplac e h and set or press ON/OFF butt on .
U NSCREEN ED T RA NS FER
1. Press TRANS button and dial station number.
2. When the called extension begins to s ignal,
hang up to transfer the call.
3. Replace hand set o r pres s ON/OFF bu tto n.
SCREEN ED T RA NS FER
While connected to an outside line:
1. Press station button where call is to be
transferred (if programmed on your
te lep ho ne),
-o r-
Press the TRANS button and dial the desired
station number.
(The called extension signals according to the
intercom signal switch position.)
2. When that extension answers, announce the
tr ans fer .
3. Hang up to complete transfer.
LEA VING A MS G WAITING I NDICAT ION
If you dial a station that is busy, unattended, or in
Do Not Disturb, you can leave a message waiting
indication.
1. Press the ON/OFF button.
2. Dial the desired intercom station. A busy tone
or DND ton e is he ard.
3. Press the MSG button. The called party’s MSG
button LED will flash slowly.
4. Press the ON/Off button to end the call.
To Next Page
Loading...