JLG RT3369 - 3.19 Decals; Rt2669, Rt3369

128 pages

Save Page as PDF

To Next Page

To Previous Page

SECTION 3 - MACHINE CONTROLS, INDICATORS, AND MACHINE OPERATION

3-42 31217162

3.19 DECALS

RT2669, RT3369

207

111 104

208

201

109

206

210

211

207

109

209

ANSI

China

ANSI Export

CE/AUS

105

103

102

OAD02270

Main Page

Table of Contents7
Section 1. Safety Precautions11
General11
Pre-Operation11
Operator Training and Knowledge11
Workplace Inspection12
Machine Inspection12
Operation13
General13
Trip and Fall Hazards14
Electrocution Hazards15
Tipping Hazards16
Crushing and Collision Hazards19
Towing, Lifting, and Hauling20
Maintenance20
General20
Maintenance Hazards20
Battery Hazards21
Section 2 - User Responsibilities, Machine Preparation, and Inspection23
Personnel Training23
Operator Training23
Training Supervision23
Operator Responsibility23
Machine Familiarization24
Preparation, Inspection, and Maintenance24
Inspection and Maintenance Table25
Pre-Start Inspection26
Walk-Around Inspection28
Function Check32
Oscillating Axle - Lockout Cylinder Test (if Equipped)34
CE Market Only34
All Markets (Except CE)36
Section 3. Machine Controls, Indicators, and Machine Operation37
General37
Description37
Operating Characteristics and Limitations38
Placards38
Capacities38
Stability38
Platform Loading38
Battery Charging (Ert Machines)39
Ground Control Station41
RT Machines41
ERT Machines42
Ground Controls43
Display Gauge45
Platform Control Station47
RT Machines47
ERT Machines48
Platform Controls49
Indicator Display51
RT Machines (if Equipped with Leveling Jacks)51
RT Machines52
ERT Machines (if Equipped with Leveling Jacks)53
Indicators54
Platform Control Indicator Display58
Navigating the Display58
Submenus60
3.10 Engine Operation61
Starting Procedure61
Dual Fuel System (if Equipped)62
3.11 Driving63
Steering63
Driving Forward63
Driving in Reverse64
Traveling on a Grade64
Grade and Sideslope65
3.12 Platform67
Raising67
Lowering67
Arm Guards (if Equipped)67
Platform Extension68
Leveling Jacks (if Equipped)68
Auto-Leveling68
Manual Level Adjustment (Trim)69
Quiklevel Advanced (Dual Oscillating Axles)70
(If Equipped)70
Auto-Leveling70
Manual Level Adjustment (Trim)71
3.15 Parking and Stowing71
3.16 Tie Down/Lifting72
Tie down72
Lifting72
3.17 Towing74
3.18 Platform Rails Fold-Down Procedure74
3.19 Decals78
Rt2669, Rt336978
Ert2669, Ert336984
Section 4 - Emergency Procedures89
General89
Incident Notification89
Emergency Towing Procedures89
RT Machines89
ERT Machines90
Emergency Operation91
Use of Ground Controls91
Operator Unable to Control Machine91
Platform Caught Overhead91
Righting of Tipped Machine92
Post-Incident Inspection92
Platform Manual Descent Control92
Section 5. Accessories93
Available Accessories93
Footswitch94
Generator (2500W)94
Output94
Safety Precautions94
Preparation and Inspection95
Operation95
Section 6 - General Specifications and Operator Maintenance97
Introduction97
Supplemental Information Only Applicable to97
Ce Machines97
EC Declaration of Conformity98
Machine Specifications99
Operating Specifications99
Dimensions101
Maximum Allowable Operating Slope101
Platform Capacity102
Fluid Capacities103
Batteries (ERT Machines)103
Tires103
Engine104
Battery Charger (ERT Machines)105
Hydraulic Oil105
Fluid Operating Temperature Specifications108
Operator Maintenance and Lubrication112
General Maintenance Tips112
Safety Prop113
Battery Disconnect (ERT Machines)114
Fuel Tank114
Hydraulic Oil Tank115
Drive Hub115
Scissor Arms Wear Pads115
Engine Coolant116
Air Filter116
Oil Change with Filter117
Fuel/Water Separator Filter (Diesel)118
Fuel Strainer (Diesel)118
Fuel Filter (Gas)119
Battery Maintenance and Charging119
Battery Charging (Daily)119
Battery Maintenance (Quarterly)120
Propane Fuel System121
Pressure Relief121
Leak Test121
Tires and Wheels122
Tire Damage122
Tire Replacement122
Wheel Replacement122
Wheel Installation123

JLG RT3369 - 3.19 Decals; Rt2669, Rt3369

Table of Contents

Other manuals for JLG RT3369

Related product manuals