KBR multicomp D6 7 Series - Page 152

152 pages

Save Page as PDF

To Previous Page

24905_EDEBDA0272-5019-1_EN

Am Kiefernschlag 7

D-91126 Schwabach

Germany

T +49 (0) 9122 6373 - 0

F +49 (0) 9122 6373 - 83

E info @ kbr.de

www.kbr.de

KBR Kompensationsanlagenbau GmbH

Main Page

Table of Contents2
User Manual6
Introduction6
Safety Notes8
Product Liability9
Disposal9
Overvoltage and Lightning Protection9
Installation and Assembly10
Connecting the Multicomp D6-XXX-710
Connection Diagram12
Terminal Assignment14
Device Memory16
Commissioning Guideline for the Multicomp D6-XXX-717
Controller Not Configured18
Default Settings after Reset20
Stage Resonance Frequency Monitoring22
Functions of the Controller in the Securec Safety and Maintenance Concept22
Current Consumption and Performance Monitoring of Stages23
Urrent Consumption and Performance Monitoring of Complete Cabinets23
Temperature Monitoring of Stages25
Description of Buttons and Displays27
Control and Display Panel27
Navigation and Device Displays28
Setting Range of the Configurable Parameters37
Device Programming38
Start Menu Commissioning38
Main Menu Cos Φ39
Main Menu Voltage / Current42
Main Menu Temperature43
Main Menu Module Management44
Main Menu Stages45
Sub Menus Mode46
Main Menu U H Voltage Distortion Factor47
Main Menu I H Distortion Current48
Main Menu Extras50
Commissioning52
Submenu Transformer Settings53
The Voltage Transformer Submenu Contains the Following Items53
Target Cosine and Freeze Mode Submenu54
Q-Control56
Dynamic Adaption of the Target Cosine-Phi (Target Q/P )58
Settings82
5.13.8.1 Submenu Modules/Display82
5.13.8.2 Submenu System90
5.13.8.3 Service Submenu102
Messages105
5.13.9.1 Submenu Messages105
Setting Transformer Ratio109
Basic Device Configuration109
Set Target Cosφ112
Notes on Troubleshooting113
System and Safety Devices Maintenance114
Temperature Limits114
Measuring Accuracy115
Device Memory115
Technical Data115
Power Supply116
Hardware Inputs116
Hardware Outputs117
Electrical Connection118
7.9 Ambient Conditions / Electrical Safety119
General Technical Data for Modules (Except Multimess D4)120
Appendix120
Relay Output Module Multisio D2 4RO121
Connection Diagram for Relay Output Module121
Relay Output Module LED Display121
Function of Scan Button122
DIP Switch Functions122
Connection Diagram for Relay Output Module123
Function Description of the Relay Output Module Multisio D4-4RO ISO123
Relay Output Module LED Display124
Function of Scan Button124
DIP Switch Functions125
Operating Mode125
DIP Switch Settings125
Technical Data126
Temperature Module Multisio D2 1TI2RO128
Temperature Module Connection Chart128
Temperature Module LED Display129
Function of Scan Button129
DIP Switch Functions130
Current Measurement Module Multisio D2-4CI131
Current Measuring Module Connection Chart131
Current Measurement Module LED Display132
Function of Scan Button132
Measuring Accuracy133
Measuring Principle133
Technical Data of the Multimess D4 Measuring Module133
Device Memory134
Power Supply134
Hardware Inputs and Outputs134
Inputs134
Outputs134
Electrical Connection135
Mechanical Data135
Standards and Miscellaneous136
Commissioning the Multimess D4 at the Multicomp D6-XXX-7136
Connections137
Analog Input Module Connection Diagram139
Multisio D2-4AI Analog Input Module139
Analog Input Module LED Display140
Function of Scan Button141
Function of DIP Switch141
Technical Data142
Multisio D2-4DI Digital Input Module144
Digital Input Module LED Display145
Function of Scan Button145
Function of the DIP Switches146
Operating Mode146
DIP Switch Settings147
Technical Data148

KBR multicomp D6 7 Series - Page 152

Table of Contents

Related product manuals