Keithley 6482 - Page 344

Model 6482 Dual-Channel Picoammeter / Voltage Source Reference Manual Index
6482-901-01 Rev. A / August 2012 I-3
disabling .........................................1-10
Format
............................................1-10
format
.............................................1-10
menus
............................................1-23
readings
...............................6-3, 16-27
remote programming
......................1-11
resolution
..........................................4-3
display subsystem
................................16-25
E
electrical power ........................................5-5
electromagnetic interference (emi)
.......... D-8
electrostatic interference
......................... D-7
environmental conditions
......................17-13
line power
.....................................17-13
temperature and relative humidity
17-13
warm-up period
............................17-13
event detection
...............................8-3, 8-15
event enable registers
programming
................................16-50
event registers
reading
.........................................16-50
examples
*OPC programming
........................14-3
*SAV, *RCL programming
..............14-4
*TRG programming
........................14-5
custom sweep
..................................7-4
custom sweep programming
..........7-13
data store programming
...................6-6
external triggering
............................8-8
filter programming
..........................4-12
limit test programming
....................10-8
math function programming
.............5-6
measurement programming
...........3-10
output configuration
........................11-5
program and read register set
......13-16
programs
..........................................F-1
range and digits programming
.........4-4
ratio & delta function programming
..5-9
read error queue programming
....13-18
rel programming
...............................5-4
remote command line frequency
......1-9
remote trigger
.................................8-20
set MSS (B6) error programming
...13-9
speed programming
.........................4-5
staircase sweep programming
.......7-12
sweep and list programming
........16-49
F
factory defaults .......................................1-12
filter
...........................................................4-6
average
........................................16-38
commands
......................................4-11
configuration
.....................................4-9
configuration menu
.........................4-10
configure and control
....................16-38
control
..............................................4-9
median filter
..........................4-7, 16-39
menus
............................................1-20
moving filter
......................................4-8
programming example
...................4-12
remote programming
......................4-11
repeat filter
.......................................4-6
stages
.............................................. 4-6
flow control
........................................... 12-14
format subsystem
................................. 16-28
front panel
................................................ 1-5
front panel calibration
........................... 17-17
front panel calibration summary
........... 17-18
front panel operation
autozero
........................................... 3-4
data store
......................................... 6-2
filter
.................................................. 4-6
gpib
................................................ 12-7
ground connect
................................ 3-6
line frequency
.................................. 1-9
math functions
................................. 5-5
measurement procedure
.................. 3-8
menus
............................................ 1-15
output configuration
....................... 11-4
range and digits
............................... 4-2
RATIO and DELTA
.......................... 5-8
relative offset (REL)
......................... 5-2
source delay
.................................... 3-5
speed
............................................... 4-4
sweep operation
.............................. 7-5
fuse replacement
........................... 1-9, 18-2
G
general information .................................. 1-2
get (group execute trigger)
..................... 12-6
go to local
GTL
................................................ 12-6
gpib
........................................................ 12-3
connections
.................................... 12-3
defaults
.......................................... 8-18
description
.......................................C-3
front panel operation
...................... 12-7
primary address
............................. 12-5
standards
....................................... 12-3
status indicators
............................. 12-7
gpib 488.1 protocol
..................................E-1
differences
.......................................E-2
selecting
...........................................E-2
grading mode limits operation
fail condition
................................... 10-5
pass condition
................................ 10-5
ground connect mode
.............................. 3-6
commands
....................................... 3-6
connections
...................................... 2-7
selecting
....................................... 16-44
ground loops
............................................D-6
H
handshaking ........................................ 12-14
I
idle ................................................. 8-2, 8-14
indicators
.................................................. 1-6
initiate
.................................................... 8-14
interface
selecting
......................................... 12-2
interface function codes
.........................C-12
introduction
................................ 17-13, 18-2