Lenze EPM-T110 - Page 11

Total index
2
Guide
2.3
l
2.3-2
EDSPM-TXXX-3.0-04/2004
4xanalog input /output
- Connection, 5.12-2
- Status display, 5.12-2
- Technical data, 5.12-3
- Terminal assignment, 5.12-2
4xanalog output
- Connection, 5.11-2
- Description, 5.11-1
- Features, 5.11-1
- Overview, 5.11-1
- Status display, 5.11-2
- Technical data, 5.11-3
- Terminal assignment, 5.11-2
4xrelay
-Description, 5.8-1
- Features, 5.8-1
-Overview, 5.8-1
- Status display, 5.8-2
- Technical data, 5.8-3
- Terminal assignment, 5.8-2
- Wiring diagram, 5.8-2
8xdig. I/O compact
-Description, 6.2-1
- Fault indications, 6.2-4, 6.3-4, 6.4-4, 6.5-4
- Features, 6.2-1
-Overview, 6.2-1
-Statusdisplay,6.2-4,6.2-5,6.3-4,6.4-4,6.5-4
- Technical data, 6.2-7
- Terminal assignment, 6.2-5
- Wiring diagram, 6.2-6
8xdigital input
- Connection, 5.3-2
-Description, 5.3-1
- Features, 5.3-1
-Overview, 5.3-1
- Status display, 5.3-2
- Technical data, 5.3-2
- Terminal assignment, 5.3-2
8xdigital input / output
- Connection, 5.9-2
- Features, 5.9-1
- Status display, 5.9-2
- Technical data, 5.9-3
- Terminal assignment, 5.9-2
8xdigital input /output
-Description, 5.9-1
-Overview, 5.9-1
8xdigital output 1A
- Connection, 5.5-2
-Description, 5.5-1
- Features, 5.5-1
-Overview, 5.5-1
- Status display, 5.5-2
- Technical data, 5.5-2
- Terminal assignment, 5.5-2
8xdigital output 2A
- Connection, 5.7-2
-Description, 5.7-1
- Features, 5.7-1
-Overview, 5.7-1
- Status display, 5.7-2
- Technical data, 5.7-2
- Terminal assignment, 5.7-2
A
Analog inputs, Status request, 9.11-5, 10.11-5
Analog modules
- 4xanalog input, Parameter setting, 12.3-1
- 4xanalog input / output, Parameter setting, 12.3-4
- 4xanalog output, Parameter setting, 12.3-3
- Converting measured values, 12.3-16
- Transmitting input data, 12.3-7
- Transmitting output data, 12.3-7
Analog outputs, #Status request, 9.11-5, 10.11-5
Application, as directed, 1.4-1
Application as directed, 1.4-1
Application examples, I/ O system IP20 on the
controller 93xx, 11.3-1
B
Baud rate
- Setting, 9.6-1, 10.6-1
- Setting at the CAN Gateway, 5.2-3, 6.2-3, 6.3-3,
6.4-3, 6.5-3
C
Cable resistance, 8.5-1
Cable type, 8.5-1
CAN Gateway
-Baudratesetting,5.2-3,6.2-3,6.3-3,6.4-3,6.5-3
- Setting the node address, 5.2-3, 6.2-3, 6.3-3, 6.4-3,
6.5-3
CAN gateway
-Description, 5.2-1
- Fault indications, 5.2-4
- Features, 5.2-1
-Overview, 5.2-1
- Status display, 5.2-4
- Technical data, 5.2-5
Show/Hide Bookmarks