What to do if result memory is full on Mahr Measuring Instruments?
If the USB memory of your Mahr Measuring Instruments is full and cannot accept further results files, transfer the saved results files to a computer via the USB interface and then delete the results files from the USB memory.
Why is the battery symbol displayed on my Mahr Measuring Instruments?
If the battery symbol is displayed on your Mahr Measuring Instruments, it means the battery is nearly empty. You should charge the battery; approximately 7 hours (M 300) or 1 hour (RD 18) is required to charge the battery to full capacity.
What to do if there is a printer error on Mahr Measuring Instruments?
If you are experiencing a printer error with your Mahr Measuring Instruments, consider these potential causes and solutions: * No paper: Load a paper roll. * The printer head is overheated: Switch off the instrument for approximately 10 minutes. * The printer is defective: If this appears repeatedly, send the instrument in for repair.
How to fix a discharged battery on Mahr Measuring Instruments?
If your Mahr Measuring Instruments indicate that the battery is discharged, it means the battery is empty. Charge the battery; approximately 7 hours is required to charge the battery to full capacity.
What to do if I experience data loss on Mahr Measuring Instruments?
If you experience data loss (instrument settings) when switching on your Mahr Measuring Instruments, select new instrument settings.
Why is the Bluetooth transmission distance short on my Mahr Measuring Instruments?
If the Bluetooth transmission distance is less than 4 meters (13 ft) on your Mahr Measuring Instruments, it could be due to: * An obstacle in the direct line of sight: Remove the obstacle if possible and ensure you can see the front side of the MarSurf M 300. * A strong transmitter nearby: Remove the transmitter if possible.
What does 'Upper limit exceeded!' mean on Mahr Measuring Instruments?
If the 'Upper limit exceeded!' message appears on your Mahr Measuring Instruments, it means the upper limit of the measuring range has been exceeded, and the measurement has been aborted. Realign the testpiece or drive unit as appropriate.
What does 'Low limit exceeded!' mean on Mahr Measuring Instruments?
If the 'Low limit exceeded!' message appears on your Mahr Measuring Instruments, it means the lower limit of the measuring range has been exceeded, and the measurement has been aborted. Realign the testpiece or drive unit as appropriate.
What does 'Timeout reached!' mean on Mahr Measuring Instruments?
If the 'Timeout reached!' message appears on your Mahr Measuring Instruments, and the M 300 is attempting to set up a Bluetooth connection with an RD 18 (or searching for existing drive units) but cannot connect, switch off both devices. Move the reset switches to the left into the "0" position, then back to the right again. Switch on first the RD 18 and then the M 300.
Why does my Mahr Measuring Instruments say 'Connect AC adapter!'?
If the 'Connect AC adapter!' message appears on your Mahr Measuring Instruments, the M 300 battery is empty. Connect the AC adapter to the M 300 and load the battery.
Covers reading documentation, specific use, avoiding hazards, and proper handling.
Describes how measured profiles are analyzed and evaluated using various parameters.
Instructions for charging the internal batteries of the MarSurf M 300 and RD 18.
Procedures for configuring instrument parameters and standards.
Covers selecting standards, managing timeout functions, and blocking settings with a code.
Details measurement and evaluation conditions according to ISO, ASME, and JIS standards.
Details measurement and evaluation conditions according to the MOTIF standard.
How to select parameters and set tolerance limits for evaluation.
How to assign functions to the programmable F1 and F2 keys.
Steps to set up the instrument for mobile operation.
Guide for mounting and setting up the instrument for stationary use.
Procedure to select the correct pick-up type and its measuring range.
Steps to establish a wireless Bluetooth connection between devices.
Instructions for performing surface texture measurements with the instrument.
Describes how to interpret and analyze measurement results.
Lists all parameters that can be calculated and evaluated by the instrument.
Guide on how to save measured profiles to the internal USB memory.
Instructions for saving measurement results and sequences.
How to manually enter a correction value for the pick-up.
General| Measuring Principle | Inductive |
|---|---|
| Resolution | 8 nm |
| Probe Tip Radius | 2 µm |
| Measuring Force | 0.75 mN |
| Storage Temperature | -20°C to 70°C |
| Resolution (nm) | 8 nm |
| Resolution (µm) | 0.008 µm |
| Power Supply | Battery or mains |
To Next Page