EasyManuals Logo

Manitowoc Grove GRT9165 User Manual

Manitowoc Grove GRT9165
476 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #101 background imageLoading...
Page #101 background image
Grove Published 7-23-2020, Control # 668-02 3-27
GRT9165 OPERATOR MANUAL OPERATING CONTROLS AND FEATURES
3
Enabling one craning function (hoist, lift, telescope, or swing)
using its related Enable/Disable Switch will cause the engine
speed to increase to 1200 rpm. Disabling all craning
functions will cause the engine speed to decrease to
750 rpm.
Luffing Boom Extension Enable/Disable
Switch (Optional)
The Luffing Boom Extension Enable/Disable Switch (9,
Figure 3-17) (Optional) is a two-position momentary switch
that is located on the right armrest.
Push switch one time to enable the luffing boom extension
function. Push switch again to disable the luffing boom
extension function.
The Luffing Boom Extension Enable/Disable Indicator in the
Status Bar area (6, Figure 4-74) of the Operating Display
Module (ODM) comes on (green) when the luffing boom
extension function is enabled. The indicator goes off when
the luffing boom extension function is disabled.
Boom Telescope Enable/Disable Switch
The Boom Telescope Enable/Disable Switch (10,
Figure 3-17) is a two-position momentary switch that is
located on the left armrest.
Push switch one time to enable the boom telescope function.
Push switch again to disable the boom telescope function.
The Telescope Enable/Disable Indicator in the Status Bar
area (6, Figure 4-74) of the Operating Display Module
(ODM) comes on (green) when the telescope function is
enabled. The indicator goes off when the telescope function
is disabled.
Enabling one craning function (hoist, lift, telescope, or swing)
using its related Enable/Disable Switch will cause the engine
speed to increase to 1200 rpm. Disabling all craning
functions will cause the engine speed to decrease to
750 rpm.
Boom Lift Enable/Disable Switch
The Boom Lift Enable/Disable Switch (11, Figure 3-17) is a
momentary switch that is located on the right armrest.
Push switch one time to enable the boom lift function (boom
up and boom down). Push switch again to disable the boom
lift function.
The Boom Lift Enable/Disable Indicator in the Status Bar
area (6, Figure 4-74) of the Operating Display Module
(ODM) comes on (green) when boom lift function is enabled.
The indicator goes off when boom lift function is disabled.
Enabling one craning function (hoist, lift, telescope, or swing)
using its related Enable/Disable Switch will cause the engine
speed to increase to 1200 rpm. Disabling all craning
functions will cause the engine speed to decrease to
750 rpm.
Seat Lumbar Support Adjustment Lever
The Seat Lumbar Support Adjustment Lever
(12, Figure 3-17) is located at the right side of the seat
backrest.
The lever can be set to three lumbar support positions.
Rotate lever clockwise to increase the lumbar support.
Rotate lever counterclockwise to reduce the lumbar support.
Seat Slide Lever
The Seat Slide Lever (13, Figure 3-17) is located at the lower
front of the seat.
Push Seat Slide Lever to the left and hold to allow the seat to
be moved forward or backward relative to the armrests.
Release lever when the seat is in the desired position. Make
sure that seat has reached a locked position.
Auxiliary Hoist Enable/Disable Switch
The Auxiliary Hoist Enable/Disable Switch (14, Figure 3-17)
is a two-position momentary switch located on the left
armrest.
Push switch one time to enable the auxiliary hoist function.
Push switch again to disable the auxiliary hoist function.
Quickly push the switch two times to enable the auxiliary
hoist function at high speed. Pushing and holding the switch
for approximately 2 seconds will also enable the auxiliary
hoist function at high speed.
The Auxiliary Hoist Enable/Disable Indicator in the Status
Bar area (6, Figure 4-74) of the Operating Display Module
(ODM) comes on (green) when the auxiliary hoist function is
enabled. The Indicator goes off when the auxiliary hoist
function is disabled.
The Auxiliary Hoist High Speed Indicator in the Status Bar
area (6, Figure 4-74) of the ODM comes on when the high
speed function is enabled.
Enabling one craning function (hoist, lift, telescope, or swing)
using its related Enable/Disable Switch will cause the engine
speed to increase to 1200 rpm. Disabling all craning
functions will cause the engine speed to decrease to
750 rpm.
Cab Tilt Switch
The Cab Tilt Switch (12, Figure 3-17) is located on the left
armrest.
The switch is a three-position, momentary rocker switch that
is used to tilt the cab up for easy viewing of an elevated
boom and load.

Table of Contents

Other manuals for Manitowoc Grove GRT9165

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Manitowoc Grove GRT9165 and is the answer not in the manual?

Manitowoc Grove GRT9165 Specifications

General IconGeneral
BrandManitowoc
ModelGrove GRT9165
CategoryConstruction Equipment
LanguageEnglish

Related product manuals