McConnel ROBOCUT2 RC40 - Page 79

70
McCONNEL
Error
Cause
Solution
60
Receiver error message CAN Autec Radio
Check the receiver, check the CAN line, check the LE70. If the
error persists, replace the IO Bridge
61
Receiver error message CAN Autec Radio
Check the receiver, check the CAN line, check the LE70. If the
error persists, replace the IO Bridge
62
Receiver error message CAN Autec Radio
Check the receiver, check the CAN line, check the LE70. If the
error persists, replace the IO Bridge
63
Receiver error message CAN Scanreco Radio
Check the receiver, check the CAN line, check the LE70. If the
error persists, replace the IO Bridge
64
Receiver error message CAN Scanreco Radio
Check the receiver, check the CAN line, check the LE70. If the
error persists, replace the IO Bridge
65
System error Scanreco radio
If the error persists, replace the radio transmitter / receiver unit
70
Radio control lever value incorrect
Check the remote control, check the control unit parameters. If
the error persists, replace the remote control
71
Radio control lever value incorrect
Check the remote control, check the control unit parameters. If
the error persists, replace the remote control
72
Radio control lever value incorrect
Check the remote control, check the control unit parameters. If
the error persists, replace the remote control
73
Radio control lever value incorrect
Check the remote control, check the control unit parameters. If
the error persists, replace the remote control
74
Radio control lever value incorrect
Check the remote control, check the control unit parameters. If
the error persists, replace the remote control
75
Radio control lever value incorrect
Check the remote control, check the control unit parameters. If
the error persists, replace the remote control
76
Radio control lever value incorrect
Check the remote control, check the control unit parameters. If
the error persists, replace the remote control
77
Radio control lever value incorrect
Check the remote control, check the control unit parameters. If
the error persists, replace the remote control
80
Receiver error message CAN from machine display
Check the display, check the CAN line, check the LE70. If the
error persists, replace the display
81
Machine display system error
If the error persists, replace the display
90
Machine inclinometer system error
If the error persists, replace the inclinometer
91
Receiver error message CAN from the inclinometer;
Check the inclinometer, check the CAN line, check the LE70, if
the error persists, replace the inclinometer
200
Engine protection alarm;
See SPN and FMI codes to understand the reason for the
alarm
201
Engine warning alarm;
See SPN and FMI codes to understand the reason for the
alarm
202
Stop engine alarm;
See SPN and FMI codes to understand the reason for the
alarm
203
Engine fault alarm
See SPN and FMI codes to understand the reason for the
alarm
204
Engine alarm
Battery voltage: the voltage measured by the ECU is outside
the target range
205
Engine alarm
Battery voltage: the voltage measured by the ECU is outside
the target range; the ECU activates a system response
206
Engine alarm
Coolant level: the level of coolant calculated by the ECU is less
than the minimum permitted amount
207
Engine alarm
Air heater relay indicator: the energy consumption measured
by the ECU does not fall within the permissible range or the
maximum permissible temperature of the ECU component that
powers the lamp has been exceeded
208
Engine alarm
Coolant temperature sensor: the sensor voltage measured
by the control unit does not fall within the permissible range;
the temperature of the coolant calculated by the control unit
is questionable when compared to the oil temperature, or the
value received via the CAN is incorrect
209
Engine alarm
Coolant temperature: the temperature of the coolant calculated
by the control unit is higher than the permissible range; the
ECU activates a system response
If the fault or the reason for it is not indicated in the list of faults shown, contact McConnel in order for repairs to be carried out.