Mitel 3000 - Additional VoIP Endpoint Options; Endpoint Options: Silence Suppression and RFC2833

137 pages

Save Page as PDF

To Next Page

To Previous Page

Mitel 3000

Installation & Maintenance Manual

Clip, Pedestal and installation of the DSS

NOTE: For the 20 degrees position or the 35 degrees position, refer to page

26.

6" cord (RJ11

connector)

Cord Rail

Main Page

Default Chapter2
- Table of Contents2
Table of Contents6
Fcc Information6
Safety Regulations9
Introduction11
General Overview11
- Safety Precautions During Installation and System Upgrades11
- Electrostatic Precaution (Esp)12
- Lightning and Surge Voltage Protection12
- Installation Steps13
Installing the Main Equipment14
- Equipment Location14
- Mounting the Ccu14
Modules Located in the Ccu17
- Module Location17
- Installing the Backplane Wall Bracket18
- Mounting the Ccu with Two Brackets18
- Mounting the Backplane19
Expansion Modules20
- Removing the 008 Module from the Backplane21
- Installing the 008 Module Onto the Backplane22
- Installing an Expansion Module22
- Co Line Module23
External Music-On-Hold Module27
T1/E1 Pri Module27
Connecting the Battery-Backup-Unit (Bbu) to the System28
Connecting the Battery29
- Sixteen Key Feature Phone30
- Eight Key Feature Phone30
- Eight Key Feature Phone31
- Direct Station Selection (Dss) Unit33
- Clip, Pedestal and Installation of the DSS34
- Wall-Mounting the Feature Phones35
- Door Phone36
Cabling the Unit37
- Connecting the Extensions38
- Wiring Jacks38
- Connecting T1/E1 Pri Trunks39
- Structured Wiring40
- Ccu Connections41
- Door Phone41
- Doorstrike41
- Connecting Apa (Public Address ) Amplifier41
- Connecting Apc or Printer to the Serial Port42
- Central Bell42
- Extension Module Mdf Connections42
Broadband Module Connections43
Expanding an Existing System44
- Installing an Additional Co Line Module44
- Installing Additional Extension Modules or a Broadband Module44
T1/E1 Module on the Mitel 300045
- Ti (Rbs) Settings45
- Framing and Coding on T1 (Rbs)46
- Line Build out46
- Line Gain46
- Dtmf or Pulse Dialing46
- Received Digits46
- Programming Required for T1 Pri (Isdn)47
- Programming Theq 931 Protocol on Pri (Isdn)47
- Line Build out Programming on Pri (Isdn)47
- Line Gain Programming for Pri (Isdn)47
- Additional Programming Options for T1 Pri (Isdn)47
Additional T1 Pri (Isdn) Information48
- Isdn (Pri) Called Party Number - Call Types48
- Call Type48
- Isdn T1 (Pri) Calling Party Number - Call Type49
- Dialing Numbers on Isdn (Pri)49
- Caller ID Restriction Override49
- Transit Network Selection on Isdn (T1 Pri)49
- Release Complete49
T1/ Pri Diagnostics50
- Alarm Indications50
- Dms Exchange - Lt1 Flag51
Programming Required for E1 Pri (Isdn)51
- Programming the Number of Channels (No. Channels)52
- Programming the Crc-452
- Hot Swapping Faulty Modules53
- Replacing a Faulty Module Mdf54
Replacing Faulty Pcbs54
Replacing Faulty Pcbs55
- Replacing the 008 Extension Board55
- Power Supply Unit Spare Fuse57
- Replacing the Ccu Mdf58
Power up and Test60
- Switch on60
Getting Started60
Essential Programming61
- Equipped Co Lines61
- Incoming Ringing61
- Call Restriction62
Individual Feature Phone Programming62
- Automatic Answer64
System Programming from the Programming Telephone66
- "System" Programming Options68
- "Extensions" Programming Options72
- "Lines" Programming Options75
?System” PROGRAMMING76
- System" Programming76
- Time and Date76
- To Change the System Programming Password76
- To Change the Programming Extension77
- Night Service77
- Music-On-Hold Options78
- To Configure Line Key Lights78
- Change Greetings78
- Programming System Timers80
- Local Codes (7 Number Digit Dialing)83
- Remote Notification of Voice Messages84
- To Reset the System86
- Voice Mailbox Capacity87
- Account Codes87
- Enhanced Emergency Service88
Extension Programming90
- Assigning Extension Names90
- To Configure Disconnected Extensions92
- Send Specific DID97
Line Programming102
- Outgoing Groups106
- Automatic Line Selection108
- Reversal on Idle109
- Break Supervision111
- Reversal on Answer111
- E1 Pri Interface113
- Trunk Type113
- Programming the Service Types115
- DID Line Type - Service Types116
- Loop Start Line Type - Service Types116
- Ground Start Line Type - Service Types116
- Programming the Start Types116
Recommendations for Customer Training121
Troubleshooting122
- System Not Initializing122
- No Incoming Calls122
- Extension Outgoing Locked122
- No Extension Dial Tone122
- Not Seizing a Line for Outgoing Calls122
- Door Phone Not Operating122
- Phone Reset122
- System Reset122
- Additional Troubleshooting Information123
- Caller ID124
Software Upgrade Instructions129
- Upgrading Systems and Restoring Databases When Upgrading to T1/E1 Pri130
- Technical Specification131
- Index133

Mitel 3000 - Additional VoIP Endpoint Options; Endpoint Options: Silence Suppression and RFC2833

Table of Contents

Other manuals for Mitel 3000

Related product manuals