276
10. Appendix
❾ Troubleshooting Check List
Beforecontactingyourdealerorservicepersonnel,checkthefollowinglisttobesurerepairsareneededalsoby
referringtothe“Troubleshooting”sectioninyouruser’smanual.Thischecklistbelowwillhelpussolveyourproblem
moreefciently.
* Printthispageandthenextpageforyourcheck.
Frequency of occurrence □ always □sometimes(Howoften?_____________________) □other(__________________)
Power
□
No power (POWER indicator does not light blue)� See also “Status
Indicator (STATUS)”�
Power cord’s plug is fully inserted into the wall outlet�
□
Lamp cover is installed correctly�
□
Lamp Hours Used (lamp operation hours) was cleared after
□
lamp replacement�
No power even though you press and hold the POWER but-
□
ton�
□
Shut down during operation�
Power cord’s plug is fully inserted into the wall outlet�
□
Lamp cover is installed correctly�
□
[AUTO POWER OFF] is turned off (only models with the [AUTO
□
POWER OFF] function)�
[OFF TIMER] is turned off (only models with the [OFF TIMER]
□
function)�
Video and Audio
□
No image is displayed from your PC or video equipment to the
projector�
Still no image even though you connect the projector to the PC
□
first, then start the PC�
Enabling your notebook PC’s signal output to the projector�
□
• Acombinationoffunctionkeyswillenable/disabletheexter-
naldisplay.Usually,thecombinationofthe“Fn”keyalong
with one of the 12 function keys turns the external display
on or off.
No image (blue or black background, no display)�
□
Still no image even though you press the AUTO ADJUST
□
button�
Still no image even though you carry out [RESET] in the
□
projector’s menu�
Signal cable’s plug is fully inserted into the input connector
□
A message appears on the screen�
□
(_____________________________________________)
The source connected to the projector is active and available�
□
Still no image even though you adjust the brightness and/or
□
the contrast�
Input source’s resolution and frequency are supported by the
□
projector�
□
Image is too dark�
Remains unchanged even though you adjust the brightness
□
and/or the contrast�
□
Image is distorted�
Image appears to be trapezoidal (unchanged even though you
□
carry out the [KEYSTONE] adjustment)�
□
Parts of the image are lost�
Still unchanged even though you press the AUTO ADJUST
□
button�
Still unchanged even though you carry out [RESET] in the
□
projector’s menu�
□
Image is shifted in the vertical or horizontal direction�
Horizontal and vertical positions are correctly adjusted on a
□
computer signal�
Input source’s resolution and frequency are supported by the
□
projector�
Some pixels are lost�
□
□
Image is flickering�
Still unchanged even though you press the AUTO ADJUST
□
button�
Still unchanged even though you carry out [RESET] in the
□
projector’s menu�
Image shows flickering or color drift on a computer signal�
□
Still unchanged even though you change [FAN MODE] from
□
[HIGH ALTITUDE] to [AUTO]�
□
Image appears blurry or out of focus�
Still unchanged even though you checked the signal’s resolution
□
on PC and changed it to projector’s native resolution�
Still unchanged even though you adjusted the focus�
□
□
No sound�
Audio cable is correctly connected to the audio input of the
□
projector�
Still unchanged even though you adjusted the volume level�
□
AUDIO OUT is connected to your audio equipment (only models
□
with the AUDIO OUT connector)�
Other
□
Remote control does not work�
No obstacles between the sensor of the projector and the
□
remote control�
Projector is placed near a fluorescent light that can disturb the
□
infrared remote controls�
Batteries are new and are not reversed in installation�
□
□
Buttons on the projector cabinet do not work (only models with the
[CONTROL PANEL LOCK] function)
[CONTROL PANEL LOCK] is not turned on or is disabled in
□
the menu�
Still unchanged even though you press and hold the EXIT button
□
for a minimum of 10 seconds�
To Next Page
Loading...
Need help?
General
