Neoway N11 V2 - About this Document; Scope; Audience; Change History

To Next Page

To Previous Page

N11 V2

AT Command Manual

About This Document

Scope

This document is applicable to N11 V2 series.

Audience

This document is intended for system engineers (SEs), development engineers, and test engineers.

Change History

Issue

Date

Change

Changed By

1.0

2018-09

Initial draft

Zhang Xiaofeng

Conventions

Symbol

Indication

This warning symbol means danger. You are in a situation that could cause fatal

device damage or even bodily damage.

Means reader be careful. In this situation, you might perform an action that

could result in module or product damages.

Means note or tips for readers to use the module

Main Page

Table of Contents3
About this Document7
Scope7
Audience7
Change History7
Conventions7
Related Documents8
Boot LOG Instruction9
General Commands10
Querying the Manufacturer: ATI10
Querying the Version: +CGMR10
Querying IMEI: +CGSN11
Querying the IMSI: +CIMI11
Obtaining the ICCID of the SIM Card: +CCID12
Querying the Version: +GMR12
Querying the Module Model: +CGMM13
Querying the Manufacturer: +CGMI13
Setting the Signal Indicator Status: +SIGNAL13
Mobile Device Control and Status Report16
Querying the Module Status: +CPAS16
Querying the Network Registration Status: +CREG17
GPRS Network Registration: +CGREG18
Enabling & Disabling the Terminal Display: ATE1/ATE020
Setting the Code Result Suppression Mode: ATQ21
Setting the Response Format of the Device: ATV21
Resetting to the Default Setting: ATZ22
Saving Parameter Settings: AT&W23
Resetting the Module to Factory Settings: AT&F23
Activating Multiplexing Mode: +CMUX24
Setting Module Function: +CFUN26
Enabling or Disabling the Sleep Mode: +ENPWRSAVE27
Setting the Baud Rate of the Module: +IPR28
Entering the PIN Codes: +CPIN28
Clock: +CCLK30
Enabling PIN and Querying MT and Network Device: +CLCK30
Modifying the Password of the PIN: +CPWD32
Network Service Commands33
Querying Signal Quality: +CSQ33
Selecting and Registering a GSM Network: +COPS34
Querying Base Station Information: +POSI35
GPRS Commands37
Setting PDP Format: CGDCONT37
Sending USSD Data: +CUSD38
Switching Data Mode to Command Mode39
Switching Command Mode to Data Mode: ATO40
Setting Network APN: +NETAPN40
Setting up a PPP Link: +XIIC41
Setting GPRS Attach and Detach: +CGATT42
SMS Commands44
Setting Preferred SMS Storage: +CPMS44
Setting SMS Inputting Mode: +CMGF45
Setting the te Character Set: +CSCS46
Setting the SMS Indication Mode: +CNMI46
Reading SMS Messages: +CMGR48
SMS Message List: +CMGL50
Sending SMS Messages:+Cmgs53
Writing SMS Messages:+Cmgw54
Sending Stored SMS Messages:+Cmss55
Delete SMS Messages: +CMGD56
Setting the SMS Center Number: +CSCA57
Setting the Parameters of the Text Mode: +CSMP57
Displaying the Parameters of the Text Mode: +CSDH58
Selecting the Type of Cell Broadcast Messages: +CSCB59
Phonebook Commands61
Selecting Phonebook Storage:+Cpbs61
Reading the Phonebook: +CPBR62
Querying the Phonebook: +CPBF63
Writing Information to the Phonebook: +CPBW64
Reading My Number:+Cnum64
TCP Data Service66
Setting up TCP Link: +TCPSETUP66
Sending TCP Data: +TCPSEND67
Receiving TCP Data: +TCPRECV68
Closing TCP Link: +TCPCLOSE68
Querying TCP/UDP Link Status: +IPSTATUS69
Querying the Status of Data Sent by the TCP Link: +TCPACK70
Setting Data TX/RX Type: +DATAFORMAT71
UDP Data Service73
Setting up UDP Link: +UDPSETUP73
Sending UDP Data: +UDPSEND74
Receiving UDP Data: +UDPRECV75
Reading UDP Data: +UDPREAD75
Closing UDP Link: +UDPCLOSE76
Transparent Mode77
Setting up Transparent TCP Link: +TCPTRANS77
Setting up Transparent UDP Link: +UDPTRANS78
Closing a Transparent Link: +TRANSCLOSE79
TCP Server at Commands80
Setting TCP Listening for the Server: +TCPLISTEN80
Closing the Listening Connection: +CLOSELISTEN81
Closing Connections with the Client: +CLOSECLIENT81
Receiving Data from the Client: +TCPRECV(S)82
Sending Data to the Client: +TCPSENDS82
Unlimited UDP Server at Commands84
Setting UDP Listening for Server: +FUDPLISTEN84
Receiving Data from the Client: +FUDPRECV(S)85
Sending Data to the Client: +FUDPSENDS85
Closing Listening for UDP Server: +CLOSEFUDPLISTEN86
FTP at Commands87
Logging in to the FTP Server: +FTPLOGIN87
Logging out from the FTP Server: +FTPLOGOUT88
Downloading Data from the FTP Server: +FTPGET89
Uploading Data to the FTP Server: +FTPPUT91
Querying FTP Link Status: +FTPSTATUS93
HTTP Commands94
Setting HTTP Parameters:+Httppara94
Setting up HTTP Link:+Httpsetup95
HTTP Request:+Httpaction95
Closing HTTP Link: +HTTPCLOSE99
Receiving HTTP Data: +HTTPRECV99
HTTP Link Closing: +HTTPCLOSED100
HTTPS Commands101
Setting HTTPS Parameters: +HTTPSPARA101
Setting up HTTPS Link: +HTTPSSETUP102
HTTPS Request: +HTTPSACTION102
Closing HTTPS Link: +HTTPSCLOSE105
HTTPS Link Closed Report: +HTTPSCLOSED105
MQTT Command106
User Parameter Settings: +MQTTCONNPARAM106
Will Settings: +MQTTWILLPARAM106
Connection Command: +MQTTCONN107
Subscription: +MQTTSUB107
Unsubscription: +MQTTUNSUB108
Topic Publish: +MQTTPUB108
Disconnecting to the MQTT Server: +MQTTDISCONN109
Receiving Topic Content: +MQTTSUB109
Querying MQTT Connection Status: +MQTTSTATE109
Setting MQTT Mode: +MQTTMODE110
Setting MQTT Parameters: +MQTTCFG111
Ali MQTT Command112
Setting MQTT Mode: +IMQTTMODE112
Setting Device Authentication: +IMQTTAUTH112
Setting MQTT Parameters: +IMQTTPARA113
Setting up MQTT Connection: +IMQTTCONN113
Publishing a Message: +IMQTTPUB114
Subscribing a Message: +IMQTTSUB115
Unsubscribing a Message: +IMQTTUNSUB116
Receiving Publish Message: +IMQTTRCVPUB116
Querying MQTT Connection Status: +IMQTTSTATE117
Disconnecting to the MQTT Server: +IMQTTCONN118
File System Commands119
Writing Data to File: +FSWF119
Reading Data from File: FSRF120
Obtain the Size of a File: +FSFS121
Deleting a File: +FSDF121
Standard Extended at Commands122
Shutting down the Module: +CPWROFF122
Updating Time:+Updatetime122
Querying the IP Address: +DNS125
Ping Function: +PING125
Obtaining the Location of the Module: +CIPGSMLOC127
Updating BS Time: +GLTS128
A Reference Process of at Command Programming130
Content of PDU SMS Messages130
Flowchart of Sending Text SMS Messages (through UART)132
Flowchart of Sending PDU SMS Messages (through UART)133

Neoway N11 V2 - About this Document; Scope; Audience; Change History

Table of Contents

Related product manuals