OPTi CCA-TS2 - Page 298

Operator’s Manual – OPTI CCA-TS2 I-3
INDEX
references PO2-3
reproducibility PO2-2
SRC limit values PO2-1
temperature corrected A-12
P
P50 8-9
calculation A-11
reference ranges A-5
Panels
test 3-16
Parameters
blanking 3-10
calculated 3-11
measured 3-10
measurement ranges 1-1, A-1
reported 3-10
reporting units 1-1
Password
setting up/changing 3-25
Patient
data 5-8
information, customizing 3-7
report 5-11
testing 5-1
Patient ID 3-7, 3-10, 5-8
PCO2 (Dry Sensor - B-Lac Cassette)
PCO2-B-1
Clinical signicance PCO2-B-1
Correlation to Other Methods
PCO2-B-4
Interferences PCO2-B-2
Linearity PCO2-B-3
Measurement principle PCO2-B-1
Measurement range PCO2-B-1
Reference intervals PCO2-B-1
References PCO2-B-4
Reproducibility PCO2-B-3
SRC limit values PCO2-B-1
Peristaltic pump cartridge
description 1-5
replacing 6-5
pH pH-1
clinical signicance pH-1
measurement principle pH-1
measurement range pH-1
SRC limit values pH-1
temperature corrected A-12
pH (Dry Sensor - B-Lac Cassette)
pH-B-1
Clinical signicance pH-B-1
Correlation to Other Methods pH-
B-4
Interferences pH-B-2
Linearity pH-B-3
measurement principle pH-B-1
measurement range pH-B-1
Reference intervals pH-B-2
References pH-B-4
Reproducibility pH-B-3
SRC Limit Values pH-B-2
PO2 (Dry Sensor - B-Lac Cassette)
PO2-B-1
Clinical signicance PO2-B-1
Correlation to Other Methods PO2-
B-4
Interferences PO2-B-2
Measurement principle PO2-B-1
Measurement range PO2-B-1
Reference intervals PO2-B-1
References PO2-B-4
Reproducibility PO2-B-3
SRC Limit Values PO2-B-1
Pollution degree A-1
Potassium (K+) K-1
clinical signicance K-1
correlation to other methods K-3
interferences K-2
linearity K-2
measurement principle K-1
measurement range K-1
reference intervals K-2
references K-3
reproducibility K-2
SRC limit values K-1
Power button 1-7
Power connector 1-7
Power Supply
connecting 2-2
Principles of operation 1-1
Principles of procedure 8-1
Printer
description 1-5
setting up 3-26
test 7-20
Printer paper
changing 6-9
installing 2-6
Prociency testing 4-2
Protocol
communications 3-33
Pump ow
checking 7-23
Pump motor
test 7-24
Q
QC
overview 4-2
recommendations 4-3
setup 4-4
QC Lockout 3-5
QC Sample
running 4-9
QC Setup 3-3, 3-38
Quality control 4-1, 8-10
R
Ranges
normal 3-12
Reference intervals 8-11
Reinitialization
system 3-25
Reported Parameters 3-10
Report formats D-1
Reports
Conguration D-6
Control 4-15
Controls Measurement D-4
Controls Statistics D-5
Diagnostic 7-30
Error D-9, D-10
Maintenance D-8
Patient D-1
SRC 4-8
SRC Measurement D-2
SRC Statistics D-3
Routine cleaning
performing 6-10
S
Sample
collection devices 5-1, 8-3
handling and storage 5-3, 8-4
preparation 5-4
requirements 5-1, 8-3
whole blood 5-4
Sample llport
description 1-8
Sample measurement chamber (SMC)
description 1-4
Security
setting up 3-19