Rigol DS2000E Series

To Next Page

To Previous Page

RIGOL Chapter 13 System Function Setting

DS2000E User’s Guide

13-6

MAC Address

For each oscilloscope, the MAC address is unique. When attributing IP address for

the oscilloscope, the MAC address is usually used to identify the instrument.

VISA Address

Display the VISA address currently used by the oscilloscope.

Main Page

Guaranty and Declaration3
Safety Requirement4
- Safety Terms and Symbols7
- Allgemeine Sicherheits Informationen8
- Sicherheits Begriffe und Symbole11
- Measurement Category12
- Ventilation Requirement13
- Working Environment14
- Care and Cleaning16
- Environmental Considerations17
DS2000E Series Overview18
Document Overview20
- Table of Contents23
Chapter 1 Quick Start29
- General Inspection30
- Appearance and Dimensions31
- To Prepare the Oscilloscope for Use32
- Front Panel Overview36
- Rear Panel Overview38
- Front Panel Function Overview40
- User Interface47
- To Use the Security Lock51
- To Use the Built-In Help System52
Chapter 2 To Set the Vertical System53
- To Enable the Analog Channel54
- Channel Coupling55
- Bandwidth Limit55
- Probe Ratio56
- Input Impedance57
- Waveform Invert57
- Vertical Scale58
- Vertical Expansion59
- Amplitude Unit59
- Channel Label59
- Delay Calibration61
Chapter 3 To Set the Horizontal System63
- Delayed Sweep64
- Time Base Mode66
- Horizontal Scale70
- Horizontal Reference71
Chapter 4 To Set the Sample System73
- Acquisition Mode74
- Sample Mode77
- Sample Rate78
- Memory Depth80
- Anti-Aliasing81
Chapter 5 To Trigger the Oscilloscope83
- Trigger Source84
- Trigger Mode85
- Trigger Coupling86
- Trigger Holdoff87
- Noise Rejection88
- Trigger Type89
- Trigger Output Connector130
Chapter 6 MATH and Measurements131
- Math Operation132
- Auto Measurement144
- Cursor Measurement159
Chapter 7 Protocol Decoding169
- Parallel Decoding170
- RS232 Decoding (Option)173
- I2C Decoding (Option)178
- SPI Decoding (Option)182
- CAN Decoding (Option)185
Chapter 8 Reference Waveform189
- To Enable REF Function190
- To Set the Color190
- To Select REF Source190
- To Save REF Waveform191
- To Adjust REF Waveform Display191
- To Export to Internal or External Memory191
- To Import from Internal or External Memory192
Chapter 9 Pass/Fail Test193
- To Enable Pass/Fail Test194
- To Select Source194
- Mask Range194
- To Set Test Results Output Type196
- To Save the Test Mask197
- To Load the Test Mask197
Chapter 10 Waveform Record199
- Waveform Record200
- Record Constant on202
- Waveform Playback204
- Waveform Analysis206
  - Analysis Based on Trace210
  - Analysis Based on Pass/Fail Mask211
Chapter 11 Display Control213
- To Select the Display Type214
- To Set the Persistence Time214
- To Set the Waveform Intensity216
- To Set the Screen Grid216
- To Set the Grid Brightness216
- To Set the Menu Display216
Chapter 12 Store and Recall217
- Storage System218
- Storage Type219
- Internal Storage and Recall221
- External Storage and Recall223
- Disk Management225
- Factory231
Chapter 13 System Function Setting239
- Remote Interface Configuration240
- System-Related246
Chapter 14 Remote Control259
- Remote Control Via USB260
- Remote Control Via LAN264
- Remote Control Via GPIB266
Chapter 15 Troubleshooting269
Chapter 16 Specifications271
Chapter 17 Appendix279
- Appendix A: Accessories and Options279
- Appendix B: Warranty280
Index281

Rigol DS2000E Series - Page 244

Table of Contents

Other manuals for Rigol DS2000E Series

Related product manuals