Rigol DS2000E Series

To Next Page

To Previous Page

Chapter 4 To Set the Sample System RIGOL

DS2000E User’s Guide 4-3

Figure 4-1 The Waveform before Average

Figure 4-2 The Waveform after 256 Averages

Main Page

Guaranty and Declaration3
Safety Requirement4
- Safety Terms and Symbols7
- Allgemeine Sicherheits Informationen8
- Sicherheits Begriffe und Symbole11
- Measurement Category12
- Ventilation Requirement13
- Working Environment14
- Care and Cleaning16
- Environmental Considerations17
DS2000E Series Overview18
Document Overview20
- Table of Contents23
Chapter 1 Quick Start29
- General Inspection30
- Appearance and Dimensions31
- To Prepare the Oscilloscope for Use32
- Front Panel Overview36
- Rear Panel Overview38
- Front Panel Function Overview40
- User Interface47
- To Use the Security Lock51
- To Use the Built-In Help System52
Chapter 2 To Set the Vertical System53
- To Enable the Analog Channel54
- Channel Coupling55
- Bandwidth Limit55
- Probe Ratio56
- Input Impedance57
- Waveform Invert57
- Vertical Scale58
- Vertical Expansion59
- Amplitude Unit59
- Channel Label59
- Delay Calibration61
Chapter 3 To Set the Horizontal System63
- Delayed Sweep64
- Time Base Mode66
- Horizontal Scale70
- Horizontal Reference71
Chapter 4 To Set the Sample System73
- Acquisition Mode74
- Sample Mode77
- Sample Rate78
- Memory Depth80
- Anti-Aliasing81
Chapter 5 To Trigger the Oscilloscope83
- Trigger Source84
- Trigger Mode85
- Trigger Coupling86
- Trigger Holdoff87
- Noise Rejection88
- Trigger Type89
- Trigger Output Connector130
Chapter 6 MATH and Measurements131
- Math Operation132
- Auto Measurement144
- Cursor Measurement159
Chapter 7 Protocol Decoding169
- Parallel Decoding170
- RS232 Decoding (Option)173
- I2C Decoding (Option)178
- SPI Decoding (Option)182
- CAN Decoding (Option)185
Chapter 8 Reference Waveform189
- To Enable REF Function190
- To Set the Color190
- To Select REF Source190
- To Save REF Waveform191
- To Adjust REF Waveform Display191
- To Export to Internal or External Memory191
- To Import from Internal or External Memory192
Chapter 9 Pass/Fail Test193
- To Enable Pass/Fail Test194
- To Select Source194
- Mask Range194
- To Set Test Results Output Type196
- To Save the Test Mask197
- To Load the Test Mask197
Chapter 10 Waveform Record199
- Waveform Record200
- Record Constant on202
- Waveform Playback204
- Waveform Analysis206
  - Analysis Based on Trace210
  - Analysis Based on Pass/Fail Mask211
Chapter 11 Display Control213
- To Select the Display Type214
- To Set the Persistence Time214
- To Set the Waveform Intensity216
- To Set the Screen Grid216
- To Set the Grid Brightness216
- To Set the Menu Display216
Chapter 12 Store and Recall217
- Storage System218
- Storage Type219
- Internal Storage and Recall221
- External Storage and Recall223
- Disk Management225
- Factory231
Chapter 13 System Function Setting239
- Remote Interface Configuration240
- System-Related246
Chapter 14 Remote Control259
- Remote Control Via USB260
- Remote Control Via LAN264
- Remote Control Via GPIB266
Chapter 15 Troubleshooting269
Chapter 16 Specifications271
Chapter 17 Appendix279
- Appendix A: Accessories and Options279
- Appendix B: Warranty280
Index281

Rigol DS2000E Series - Page 75

Table of Contents

Other manuals for Rigol DS2000E Series

Related product manuals