EasyManuals Logo

Roger Technology H70/104AC Instructions And Warnings For Installation

Roger Technology H70/104AC
Go to English
260 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #51 background imageLoading...
Page #51 background image
EN
51
6.2 Electrical connections
DESCRIPTION
LN
Mains power supply 230 V~ ±10% 50 Hz connection.
(H70/104AC-105AC/115V/BOX115 V~ ± 10% 60Hz).
AP-CM-CH
M
AP
CM
CH
For H70/104AC: ROGER MOTOR connection.
N.B.6IEH][MVIHMRJEGXSV]F]63+)68)',2303+=H70/104AC only).
H70/105AC ONLY. The gate open stop limit switch may be connected to terminals AP-CM and
the gate closed stop limit switch may be connected to terminals CH-CM.
;LIREPMQMXW[MXGLMWEGXMZEXIHTS[IVMWGYXXSXLIQSXSVSTIRMRKGPSWMRKXLIKEXI
'SRHIRWIVGSRRIGXMSRWIIXIGLRMGEPWTIGMƼGEXMSRWKMZIRMRXLIMRWXVYGXMSRWJSVXLIQSXSV
7 Commands and Accessories
-JRSXMRWXEPPIHWEJIX]HIZMGIW[MXL2'GSRXEGXWQYWXFINYQTIVIHEXXLI
'31XIVQMREPWSVHMWEFPIHF]QSHMJ]MRKXLITEVEQIXIVW
and .
N.B: limit switches not used with H70/105AC board must be disabled by
parameter .
/)=
N.A. (Normally Open).
N.C. (Normally Closed).
CONTACT DESCRIPTION
7(COR) 8
Connection for external power supply for courtesy light :b;ƼK
7(COR) 8
Connection for external power supply for electric lock (potential free contact) 12 V~ max 15VA
ƼK
9 10(LAM)
'SRRIGXMSRJSVI\XIVREPTS[IVWYTTP]JSVƽEWLMRKPMKLX (potential free contact):b;ƼK
3-5).
8LIWIXXMRKWJSVXLITVIQERSIYZVIƽEWLMRK[EVRMRKWMKREPQE]FIWIPIGXIH[MXLTEVEQIXIV$
[LMPIXLIƽEWLMRKQSHIMWWIX[MXLTEVEQIXIV.
11(24V~) 13(COM)
Power feed for external devices 6 W.
12(SC) 13(COM)
Connection for gate open indicator lamp 24 V ;WIIƼK
The function of the indicator lamp is determined by parameter $.
12(SC) 13(COM)
Photocell test connectionWIIƼK
feed for the photocell transmitters (TX) may be connected to this.
Set the parameter $  to enable the test function.
)EGLXMQIEGSQQERHMWVIGIMZIHXLIGSRXVSPYRMXW[MXGLIWXLITLSXSGIPPWSJJERHSRXSGLIGOXLEX
the contact changes state correctly.

Table of Contents

Other manuals for Roger Technology H70/104AC

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Roger Technology H70/104AC and is the answer not in the manual?

Roger Technology H70/104AC Specifications

General IconGeneral
BrandRoger Technology
ModelH70/104AC
CategoryControl Unit
LanguageEnglish

Related product manuals