Rohde & Schwarz R&S ZNB - Page 1145

Command Reference
R&S
®
ZNB/ZNBT
1145User Manual 1173.9163.02 ─ 53
Option R&S ZNB-B1, Bias Tees
If option R&S ZNB-B1 is installed on a R&S ZNB4 or R&S ZNB8, the frequency range
starts at 100 kHz.
Bias Tees are not available for the R&S ZNBT.
[SENSe<Ch>:]FREQuency[:CW]....................................................................................1145
[SENSe<Ch>:]FREQuency:FIXed.................................................................................. 1145
[SENSe<Ch>:]FREQuency:CENTer............................................................................... 1146
[SENSe<Ch>:]FREQuency:CONVersion.........................................................................1147
[SENSe<Ch>:]FREQuency:CONVersion:ARBitrary..........................................................1147
[SENSe<Ch>:]FREQuency:CONVersion:ARBitrary:PMETer<Pmtr>...................................1147
[SENSe<Ch>:]FREQuency:CONVersion:GAIN:LMCorrection............................................1149
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:FIXed<Stg>............................................. 1149
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:FUNDamental..........................................1149
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:IFPort..................................................... 1150
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:LOMultiplier<Stg>.................................... 1150
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:LOPort<Stg>........................................... 1151
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:MFFixed..................................................1151
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:RFMultiplier............................................. 1152
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:RFPort.................................................... 1153
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:STAGes.................................................. 1153
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:TFRequency<Stg>................................... 1153
[SENSe<Ch>:]FREQuency:IMODulation:CONVersion......................................................1154
[SENSe<Ch>:]FREQuency:IMODulation:LTONe..............................................................1154
[SENSe<Ch>:]FREQuency:IMODulation:ORDer<Im>[:STATe].......................................... 1155
[SENSe<Ch>:]FREQuency:IMODulation:RECeiver..........................................................1156
[SENSe<Ch>:]FREQuency:IMODulation:SPECtrum:MORDer...........................................1156
[SENSe<Ch>:]FREQuency:IMODulation:SPECtrum[:STATe].............................................1156
[SENSe<Ch>:]FREQuency:IMODulation:TDIStance.........................................................1157
[SENSe<Ch>:]FREQuency:IMODulation:UTONe.............................................................1158
[SENSe<Ch>:]FREQuency:SBANd................................................................................ 1158
[SENSe<Ch>:]FREQuency:SEGMent:AXIS.................................................................... 1159
[SENSe<Ch>:]FREQuency:SPAN.................................................................................. 1160
[SENSe<Ch>:]FREQuency:STARt................................................................................. 1160
[SENSe<Ch>:]FREQuency:STOP..................................................................................1160
[SENSe<Ch>:]FREQuency[:CW] <FixedFreq>
[SENSe<Ch>:]FREQuency:FIXed <FixedFreq>
Defines the fixed (Continuous Wave, CW) frequency for all sweep types operating at
fixed frequency ("Power", "Time", "CW Mode"). The two command forms
[SENSe<Ch>:]FREQuency[:CW] and [SENSe<Ch>:]FREQuency:FIXed are
equivalent.
This command also defines the center frequency of the intermodulation spectrum dia-
gram (option R&S ZNB/ZNBT-K14). The frequency range depends on the R&S ZNB/
ZNBT model; see Chapter 8.3.14.10, "[SENSe:]FREQuency...", on page 1144.
SCPI Command Reference