Sagem RT3000 - Page 46

To Next Page

To Previous Page

Installing the RT3000 modem driver on a Windows-PC

SAGEM RT3000 45

Datei 8115AD002-Total.doc

Datei gespeichert 24.04.04 13:23 von EDV/ORGA

Druckzeit 24.04.04, 18:17

Status Release

10. The serial port driver for the USB interface will be installed.

11. When this dialogue is displayed:

Click Continue Anyway.

Main Page

Default Chapter5
- Table of Contents5
1 Introduction8
2 The Leds on the Device9
- GSM Signal Quality Indication9
3 Putting the Device into Operation10
- Survey10
- Inserting the SIM Card10
- Connecting the Telecomms Equipment11
- Enter the PIN Number12
- Autopin Option13
- Enter the PUK Number13
- Wall-Mounting14
4 Operation: Making and Answering Telephone Calls14
- Call a Remote Party15
- Emergency Call15
- To Answer an Incoming Phone Call15
- Option: Having Two Calls at the same Time16
5 Operation: Send and Receive Fax with a Facsimile Device18
- To Receive a Test Fax18
- In Case of a FAX Warning19
6 Operation: Analogue Modem Connections20
7 Operation: Send and Receive Fixed Network SMS21
- In Case of Error21
8 Configuration23
- Access Code for DTMF Configuration23
  - Changing the DTMF Access Code23
- Ports for Incoming Calls; Volume of Voice Signal24
  - To Select Ports for Incoming Telephone Calls24
  - Volume of Voice Signals in Telephone Calls24
- Configuration of Network Services25
- FAX-Configuration32
- Data Call Configuration33
  - Select Port for Data Calls33
- SMS Configuration34
- Additional Configuration37
9 Installing the RT3000 Modem Driver on a Windows-PC40
10 Operation: Internet Via GPRS with a PC53
- Installing the Windows Dial-Up Network Connection53
- To Connect and Disconnect To/From the GPRS / Internet59
11 Operation: Using a PC to Send and Receive Fax60
12 Operation: Using a PC to Transmit and Receive Data61
13 Operation: Using a PC to Send and Receive SMS62
14 For Experienced Users: at Commands63
- AT Command Interface63
- AT Commands Supported by the SAGEM RT300063
  - AT Command Interface (SMS)70
  - AT Command Interface (SIM APPLICATION TOOLKIT)74
15 Configuration Methods79
- Configuration by DTMF81
- Remote Configuration by SMS83
- Configuration by FTP (Local and Remote)84
16 Parameters in the File Para.ini: Advanced Configuration86
- Settings for Configuration Access Via DTMF86
- Settings for the Configuration Access Via SMS and FTP86
- Power-Missing SMS87
- Select Port for Incoming SMS88
- Select Baudrate for Debug-RS23288
- Pre-Selection89
- Prefix for International Calls89
- Prefix for Analogue Data and Fax Calls90
- Local Accepted Emergency Number90
- Port Allocation91
- Analogue Fax Configuration91
- Billing Tone Configuration93
- CLIP Function Configuration94
- Configuration of the Flash Signal95
- RING Frequency96
- Dialling Configuration96
- Call Wait Tone On/Off97
- Local Ringback Tone On/Off97
- Voice Signal Volume on Telephone and Fax/Modem/Phone Port98
- Telephone and Fax/Modem/Phone Port Impedance98
- GPRS Configuration99
- CLIR On/Off100
- PIN Number100
- AT Command Parameter101
- Polarity Reversal (Spain)101
- Hang-Up Delay101
- MNP Flow Control102
- Maximum Local Modem Speed102
- Minimum Local Modem Speed102
- GSM Speed103
- Early Connect of Local Modem103
- Data Numbers103
- GSM Baudrate Depending on Dialled Number (Number)104
- GSM Baudrate Depending on Dialled Number (Baudrate)104
- Fixed Network SMS105
- Frequency Band Selection GSM 900, DCS 1800, PCS 1900106
- Identification106
- Sample File107
17 Configuration of Tones113
- How to Program a New Timing115
- Example-File116
18 Logfile118
19 Update the Firmware119
20 Connection Sockets120
21 Technical Data121

Sagem RT3000 - Page 46

Table of Contents

Related product manuals