EasyManuals Logo

Sanyo PLC-XU301A User Manual

Sanyo PLC-XU301A
79 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #64 background imageLoading...
Page #64 background image
64
Problem: –Solutions
No power –PlugthepowercordoftheprojectorintotheACoutlet.
 –SeeifthePOWERindicatorlightsred.
 –WaituntilthePOWERindicatorstopsblinkingtoturnontheprojector
again.TheprojectorcanbeturnedonafterthePOWERindicator
turnsred.Seepage18.
 –ChecktheWARNINGindicator.IftheWARNINGindicatorlightsred,
projectorcannotbeturnedon.Seepage59.
 –Checktheprojectionlamp.Seepage62.
 –UnlocktheKeylockfunctionfortheprojector.Seepage54.
The initial display is not shown. –MakesureOfforCountdown offarenotchosenatdisplay 
function.Seepage46.
The initial display is not same –MakesureUserorOffarenotchosenatLogo(select)
as the default set. function.Seepage47.
Input signal switches automatically. –MakesureInputsearchfunctionisadjustedproperly.Seepage45.
(or does not switch automatically)
When the projector is on and you –ThatistheFilterwarningicon.Seepage56.
press the input button, an icon
other than the Lamp mode icon
appears.
An icon other than Input mode or –ThatistheLampreplacementiconortheFilterwarningicon.See
Lamp mode icon appears. pages56or62.
Image is out of focus. –Adjustfocusoftheprojector.Seepage23.
 –Provideproperdistancebetweentheprojectorandtheprojection
 screen.Seepage13.
 –Checktheprojectionlenstoseeifitneedscleaning.Seepage61.
 –Movingtheprojectorfromacooltowarmplacemayresultin

moisturecondensationontheprojectionlens.Insuchcases,leave
 theprojectoroffandwaituntilcondensationevaporates.
Image is Left/Right reversed. –ChecktheCeiling/Rearfunction.Seepage50.
Image is Top/Bottom reversed. –ChecktheCeilingfunction.Seepage50.
Picture is not bright enough. –CheckiftheContrastorBrightnessisadjustedproperly.See
 pages34,41.
 –CheckifImage modeisselectedproperly.Seepages33,40.
 –Checkthelampcontrolfunction.Seepages25,53.
 –ChecktheLAMPREPLACEindicator.Ifitlights,theendoflamplife
 isapproaching.Replacethelampwithanewonepromptly.Seepage
 62.
Appendix
Troubleshooting
Beforecallingyourdealerorservicecenterforassistance,checktheitemsbelowonceagain.
–Makesureyouhaveproperlyconnectedtheprojectortoperipheralequipmentasdescribedonpages14-16.
–MakesureallequipmentisconnectedtoACoutletandthepoweristurnedon.
–Whentheprojectordoesnotprojectanimagefromtheconnectedcomputer,restartthecomputer.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLC-XU301A and is the answer not in the manual?

Sanyo PLC-XU301A Specifications

General IconGeneral
BrandSanyo
ModelPLC-XU301A
CategoryProjector
LanguageEnglish

Related product manuals