SEW-Eurodrive DHE21B - Page 79

Manual – Controllers DHE/DHF/DHR21B (standard) and DHE/DHF/DHR41B (advanced)
79
Index
L
LED Link/Activity in EtherNet/IP and
Modbus/TCP mode ................................................47
LED L1 (CAN 1 state) ............................................27
LED L10 (24V / I/O OK) .........................................29
LED L13 (BUS FAULT) in DeviceNet mode...........38
LED L13 (BUS FAULT) in PROFINET mode.........44
LED L13 (NETWORK STATUS) in
EtherNet/IP and Modbus/TCP mode......................46
LED L14 (BIO) in DeviceNet mode ........................38
LED L14 (MODULE STATUS) in EtherNet/IP
and Modbus/TCP mode.........................................46
LED L14 (RUN) in PROFINET mode.....................44
LED L15 (PIO) .......................................................37
LED L16 (Mod/Net) ................................................37
LED L17 (PROFIBUS fault)....................................34
LED L18 (Run PROFIBUS)....................................35
LED L2 (CAN 2 state) ............................................28
LED L3 (IEC program state)...................................28
LED L4 (controller state) ........................................28
LED L5 (User) ........................................................28
LEDs in DeviceNet mode.......................................36
LED L13 (BUS FAULT)......................................38
LED L14 (BIO) ...................................................38
LED 15 (PIO) .....................................................37
LED 16 (Mod/Net)..............................................37
LEDs in EtherNet/IP and Modbus/TCP mode........46
LED Link/Activity................................................47
LED L14 MODULE STATUS .............................46
LED 13 (NETWORK STATUS)..........................46
LEDs in PROFINET mode .....................................44
LED L13 (BUS FAULT)......................................44
LED L14 (RUN)..................................................44
Link/Activity LED................................................45
LEDs L6, L7, L8, L9 (DIO n/m)...............................29
LEDs of the DHF21B/41B option
LED L17 (PROFIBUS fault) ...............................34
LEDs of the DH.21B/41B option ............................27
LED L1 (CAN 1 state) ........................................27
LED L10 (24V / I/O OK) .....................................29
LED L2 (CAN 2 state) ........................................28
LED L3 (IEC program state) ..............................28
LED L4 (controller state)....................................28
LED L5 (User)....................................................28
LEDs L6, L7, L8, L9 (DIO n/m) ..........................29
Link/Activity LED in PROFINET mode ...................45
M
MAC address.........................................................42
Meaning of the signal words....................................6
MOVIAXIS
®
master module
Functional description of terminals X5a/X5b .....17
Installing DH.21B/41B option.............................17
Wiring diagram DHE41B option.........................18
MOVIDRIVE
®
MDX61B
Installing DH.21B/41B option.......................15, 17
Installing or removing an option card.................16
MOVITRAC
®
B / stand-alone unit
Installing DH.21B/41B option.............................19
MOVITRAC
®
B/stand-alone unit
Description of terminals and LEDs ....................19
DH.21B/41B option, connecting CAN 1
system bus/voltage supply (X26).......................20
RS485 interface COM 1 (connector X24)..........19
N
Network
Direct communication ........................................58
Network classes.....................................................42
O
Option DH.21B/41B
Installation options.............................................15
Other applicable documentation ..............................8
Overview of DH.21B/41B controllers .....................11
P
Parameters
Configuring the communication channel............62
Configuring USB communication.......................56
For SMLP...........................................................65
Parameterizing units in the parameter tree........66
Reading/changing unit parameters....................66
USB communication ..........................................57
Performance class CCU standard .........................11
Performance class MOVI-PLC
®
advanced............11
Performance class MOVI-PLC
®
standard..............11
Proejct planning.....................................................50
Project planning
Replacing the unit..............................................68
R
Right to claim under warranty ..................................7
RS485 interface
Connecting DH.21B/41B option (X34)...............26
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com