How to troubleshoot fire controls fault LED 14 flashing fast on Siemens Control Unit?
A rapidly flashing fire controls fault LED 14 on your Siemens Control Unit suggests a fault on a monitored control line, specifically one programmed in step 5 to option 12 or 13. Check the line for a short circuit, break, or a missing/defective EOL.
What to check if fault LED 2 is flashing fast on Siemens Control Unit?
Check if there is another fault LED flashing. If not, check if control input Fault is activated.
Why is the power fault LED 11 flashing on my Siemens Control Unit?
The LED 11 power fault on your Siemens Control Unit flashes for two primary reasons: either the battery is disconnected or low, or the mains supply is missing after the delay has expired. To resolve this, first, replace the battery. If the issue persists, check the internal fuse or the external mains breaker.
How to fix the yellow zone LED flashing fast on Siemens Control Unit?
A rapidly flashing yellow zone LED on your Siemens Control Unit indicates a fault in zone number x. You should check if any detector head is removed and inspect the line for a short circuit, break, or a missing/defective EOL.
What to do if the alarm horn fault LED 13 is flashing fast on Siemens FC1008-A?
If the alarm horn fault LED 13 is flashing rapidly on your Siemens Control Unit, it signifies a fault in the monitored control lines (horn). Inspect the lines for a short circuit, break, or a missing/defective EOL. If a control card FCA1003 is in use, check LEDs DL1 - DL4 to identify the faulty line.
What does it mean when LED 10 earth fault is flashing fast on Siemens Control Unit?
A rapidly flashing LED 10 for earth fault on your Siemens Control Unit indicates that some part of the system has a leakage to earth. Remove external lines (detector line etc.) one by one until the fault disappears, and then repair the defective line. If no external line has a leakage to earth, consider replacing the mainboard.
Why is the RT-Fault LED 15 flashing fast on my Siemens FC1008-A Control Unit?
The rapid flashing of the RT-Fault LED 15 on your Siemens Control Unit can occur because the control input Fault RT is active, or if a programmable control input with option 1 is active indicating a fault with the remote transmission device. Check the remote transmission device. It can also mean there is a fault on a monitored control line (programmed in step 5 to option 14), so check the line for a short circuit, break, or missing/defective EOL.
What should I do if the system fault LED 12 is flashing fast on my Siemens FC1008-A?
If the system fault LED 12 is flashing rapidly on your Siemens Control Unit, it indicates that the microcomputer has failed and the system is not working. Try switching the power off and restarting the system. If the fault persists, replace the mainboard.
What does it mean when the RT-Alarm LED 23 is flashing fast on Siemens FC1008-A?
A rapidly flashing RT-Alarm LED 23 on your Siemens Control Unit indicates a fault on a monitored control line, specifically one programmed in step 5 to option 11. Check the line for a short circuit, break, or a missing/defective EOL.
Why does my Siemens FC1008-A display 88.88?
The Siemens Control Unit displaying 88.88 indicates that the clock has not been set, which typically occurs with a new system startup or after a power down. Set the date and time to resolve this.
Explains the function and configuration of mainboard hardware settings (jumpers).
Illustrates the processing logic for alarm and fault events within the system.
Outlines the steps for commissioning the system, including hardware checks and function tests.
Guides on adjusting programmable user functions via single programming steps.
Explains how to select and set programming steps for the unit.
Explains fault causes and actions based on LED flashing patterns.
General| Model | FC1008-A |
|---|---|
| Manufacturer | Siemens |
| Number of Loops | 1 |
| Redundancy | No |
| Display | LCD |
| Power Supply | 24 V DC |
| Protection Class | IP30 |
| Type | Fire Alarm Control Panel |
| Network Capability | Yes |
| Storage Temperature | -20 °C to +60 °C |
To Next Page