Siemens SINUMERIK 840D

A
Appendix 04.00
Index
A

Siemens AG 2000. All rights reserved
A-578
SINUMERIK 840D/840Di/810D/FM-NC Programming Guide Advanced (PGA) – 04.00 Edition
$AA_EG_SYN 15-572
$AA_EG_SYNFA 15-567
$AA_EG_TYPE 15-571
$AA_ENC_ACTIVE 15-559
$AA_ENC_COMP 15-534
$AA_ENC_COMP_IS_MODULO 15-535
$AA_ENC_COMP_MAX 15-534
$AA_ENC_COMP_MIN 15-534
$AA_ENC_COMP_STEP 15-534
$AA_ENC1_ACTIVE 15-559
$AA_ENC2_ACTIVE 15-559
$AA_ESR_ENABLE 15-570
$AA_ESR_STAT 15-570
$AA_ETRANS 15-561
$AA_FXS 15-567
$AA_IB 15-559
$AA_IBN 15-559
$AA_IEN 15-559
$AA_IM 15-559
$AA_IW 15-558
$AA_LEAD_P 15-568
$AA_LEAD_P_TURN 15-568
$AA_LEAD_SP 9-322, 15-568
$AA_LEAD_SV 9-322, 15-568
$AA_LEAD_V 15-568
$AA_LOAD 15-565
$AA_MEAACT 15-561
$AA_MM 15-560
$AA_MM1 15-561
$AA_MM2 15-561
$AA_MM3 15-561
$AA_MM4 15-561
$AA_MOTEND 15-570
$AA_MOTENDA 5-188
$AA_MW 15-560
$AA_MW1 15-560
$AA_MW2 15-560
$AA_MW3 15-560
$AA_MW4 15-560
$AA_OFF 15-561
$AA_OFF_LIMIT 15-561
$AA_OSCILL_REVERSE_POS1 15-563
$AA_OSCILL_REVERSE_POS2 15-563
$AA_OVR 15-564
$AA_POWER 15-565
$AA_PROG_INDEX_AX_POS_NO 15-559
$AA_QEC 15-535
$AA_QEC_ACCEL_1 15-535
$AA_QEC_ACCEL_2 15-535
$AA_QEC_ACCEL_3 15-535
$AA_QEC_COARSE_STEPS 15-535
$AA_QEC_DIRECTIONAL 15-536
$AA_QEC_FINE_STEPS 15-535
$AA_QEC_LEARNING_RATE 15-536
$AA_QEC_MEAS_TIME_1 15-535
$AA_QEC_MEAS_TIME_2 15-535
$AA_QEC_MEAS_TIME_3 15-536
$AA_QEC_TIME_1 15-536
$AA_QEC_TIME_2 15-536
$AA_REF 15-566
$AA_SCPAR 5-190, 15-570
$AA_SCTRACE 15-569
$AA_SOFTENDN 15-562
$AA_SOFTENDP 15-562
$AA_STAT 15-566
$AA_SYNC 15-568
$AA_TORQUE 15-565
$AA_TYP 15-566
$AA_VACTB 15-564
$AA_VACTM 15-565
$AA_VACTW 15-565
$AA_VC 15-564
$AC_ACTUAL_PARTS 15-558
$AC_ALARM_STAT 15-558
$AC_ASUP 15-545
$AC_AXCTSWA 15-571
$AC_CUTTING_TIME 15-558
$AC_CYCLE_TIME 15-558
$AC_DELT 15-553
$AC_DRF 15-561
$AC_DTBB 15-553
$AC_DTBW 15-553
$AC_DTEB 15-553
$AC_DTEW 15-553
$AC_FCT0 15-557
$AC_FCT1 15-557
$AC_FCT1C 15-557
$AC_FCT1LL 15-557