06.03
Index-540
Siemens AG, 2003. All rights reserved
SINUMERIK 840Di Manual (HBI) – 06.03 Edition
Bus fault, 10-397
BUSF, 10-397
C
Cabinet mounting, ADI4, 2-119
Cable distributor, 2-76
Connector assignment, 2-78
Cable outlet, 2-47
Cable routing, ADI4, 2-119
Certification , expansions, 1-26
Changing the battery
Criteria for, 2-50
MCI board, 2-50
Channel axes, 10-308
Checklist, Preparing for start-up, 6-173
Circularity test, 13-417
Clamping tolerance, 10-343
Clearance-coded reference marks, 10-355
Closed-loop control circuits, 10-332
Color depth
Setting, 1-25
Switchover, 1-25
Commissioning
PLC, 8-249
Recommended order, 6-174
Compile cycles, 10-389
Boundary conditions, 10-391
Retrofitting, 10-390
Complete system, 2-43
Computational resolution, 10-281
Computer name, 6-188, 6-200
Configuration
Loading into the PLC, 7-244, 7-246
Operating a PLC with a new
configuration, 7-246
Connection overview
ADI4, 2-122
MCI board, 3-131
MCI board extension, 3-131
PCU 50, 3-131
Contour monitoring, 10-347
Control direction, 10-332
Coordinate axes, 10-308
Correct shutdown, 1-29
CPU time share, 10-292
Current control loop, Measurement, 13-423
Current HMI–Environment, 6-189
Customizable message frame configuration,
16-501
Cycle times, 10-290
Cycles
Changing, 10-306
Option, 10-306
Relocation, 10-306
Saving, 10-306
Swapping, 10-306
Cyclic operation, PLC, 8-259
D
Data backup, 14-449
611u, 14-450
PLC data, 14-453
Time, 14-449
Various components, 14-449
Data Exchange Time, 7-205
Data loss, 10-304
Data transfer rate
HHU, 5-154
HT 6, 5-163
MCP, 5-142
MPI interface, 5-149
PCU with HMI Advanced, 5-168
Declaration of Conformity, C-535
Default address assignment, 5-139
Default password, 10-278
Deleting NC data, 8-250
Detailed view, 7-212
Diagnosis
NC, 10-395
PLC, 10-395
Differential handwheels, 2-68
Dimension drawing
ADI4, 2-123
MCI board extension backpack, 2-75
PP72/48, 2-103
Display resolution, 10-281, 10-282
PCU with Advanced, 5-168
Distributed I/Os, 10-397
DMF file
General, 7-209
I/O module PP72/48, 1-33
DOS Shell, 6-195
DP cycle, 7-205, 7-241
Setting, 7-213
DP cycle time, 7-205
DP master, 7-213
DP slave 611U
Consistency, 7-231, 7-235
Inserting into an S7 project, 7-231
PROFIBUS DP communication, 7-236
Setting the I/O addresses, 7-234
Setting the message frame type, 7-233
Setting the PROFIBUS address, 7-232
DP slave 611u, PROFIBUS parameters, 7-232
DP slave ADI4
Boundary conditions in SW 2.1 and
higher, 7-229
Consistency, 7-224
Setting the I/O addresses, 7-223
Setting the PROFIBUS address, 7-221
DP slave PP72/48
Inserting, 7-217
PROFIBUS parameters, 7-218
Selecting the set configuration, 7-218
Setting the I/O addresses, 7-219
DP-Slave 611U, Parameterization, 7-232
Index
To Next Page
Loading...
