Sony MVS-3000 System - Displaying a List of Transition Rates and Changing the Settings; AUX Menu Operations; AUX Bus Settings

126
AUX Menu Operations
Chapter 8 Color Backgrounds, Copy and Swap, and Other Settings
Displaying a List of Transition Rates
and Changing the Settings
In the Misc >Transition >Key/ME/FTB menu (3231), for
each bank you can display a list of the M/E (or PGM/PST)
transition rates and independent key (or DSK) transition
rates, and change the settings.
These settings are linked to the other transition rate setting
operations.
You can also display and set the fade-to-black transition
rate.
Menu display
The display of the independent key transition rate in the
Misc >Transition Key/ME/FTB menu (3231) depends on
the selection in the <Key Transition> group of the
Engineering Setup >Switcher >Transition menu (7334) for
each of the switcher banks.
When [Same] (On direction and Off direction settings
are the same) is selected in the <Key Transition>
group: Only “Key” (or “DSK” in the PGM/PST bank)
appears.
When [Independ] (On direction and Off direction
settings are independent) is selected in the <Key
Transition> group: “Key(On)” and “Key(Off)” each
appear. In the PGM/PST bank, “DSK(On)” and
“DSK(Off)” appear.
For details, 1 “Settings Relating to Video Switching”
(p. 250).
Setting the transition rate
To set the M/E transition rate
For example, to make the settings for the M/E-1 bank, use
the following procedure.
1 In the status area if the Misc >Transition Key/ME/FTB
menu (3231), press [M/E-1].
2 In the <Transition Rate> group, press [Transition].
3 Set the number of frames.
When a clip transition is selected as the transition type, it
is not possible to change the transition rate in this menu.
To set the independent key transition rate
For example, to make the settings for keys 1 to 4 in the
M/E-1 bank, use the following procedure.
1 In the status area if the Misc >Transition >Key/ME/
FTB menu (3231), press [M/E-1].
2 In the <Transition Rate> group, press [Key K1-K4].
To insert (on) or remove (off) keys individually, press
[Key(On) K1-K4] or [Key(Off) K1-K4].
3 Set the number of frames.
Setting the fade-to-black transition rate
1 In the Misc >Transition >Key/ME/FTB menu (3231),
press [FTB].
2 Set the number of frames.
AUX Menu Operations
AUX Bus Settings
In the AUX menu, you can make color corrector settings
for an AUX bus.
Setting the AUX bus color corrector
In the Engineering Setup >Switcher >Key/Wipe/FM/CCR
>CCR menu (7335.3), you can make settings for an AUX
bus for which color correction is enabled.
1 In the Aux >Aux Bus menu (2311), select the AUX
bus to which the settings apply.
2 In the <CCR> group, press [CCR], turning it on.
3 Make the following settings, as required.
To set video processes: Turn on [Video Process] in
the <Video Process> group.
To set primary color correction: Turn on [Primary
CCR] in the <Primary CCR> group, and select the
item to set in the <Primary CCR Adjust> group.
No. Parameter Adjustment
1 Transition Rate Transition rate
Notes
No. Parameter Adjustment
1 Key1 Trans Rate Key 1 transition rate
2 Key2 Trans Rate Key 2 transition rate
3 Key3 Trans Rate Key 3 transition rate
4 Key4 Trans Rate Key 4 transition rate
No. Parameter Adjustment
1 Transition Rate Transition rate