186
To change the playback speed
Set the [Variable Speed] button to the on state and set the
foll
owing parameter.
When the [Variable Speed] button
is set to the on state,
audio is not played.
To delete regions outside the playback range
(tri
mming)
Press the [Trim] button, check the message, then press
[O
K].
The region before the set playback start point and the
regi
on after the set playback stop point are deleted.
• Trimming is disabled when video content is in the
fo
llowing states on any of the frame memory output
channels.
– Playing
– Recalled on a locked frame memory output channel
• For content present in content st
orage, trimmed content
is saved as new content with a name having a “_TRM”
suffix. The original content is not deleted.
For content present in frame memory only, the original
cont
ent is trimmed and saved in frame memory. It is not
saved in content storage.
Playing video (device control block)
The device control block can be switched to device/frame
memory/clip player operation mode for playback control
of video.
For details about the operation buttons in device/frame
me
mory/clip player operation mode, see “VTR/disk
recorder operations” (page 218).
The buttons used for selecti
ng a frame memory output
channel must be assigned to the device control block
beforehand.
For details about assign
ing buttons, see “Assigning
Control Panel Buttons” (page 397).
1
Press the [DEV] button.
The [DEV] button is lit amber, and the operation
mode
switches to device/frame memory/clip player
operation mode.
2
Press the [FM1 CLIP] button.
The [FM1 CLIP] button is lit green, and frame
me
mory output channel 1 becomes the target of
operations.
When group mode is enabled, the buttons for the two
combined fram
e memory output channels are lit.
3
Press the [PLAY] button.
The [PLAY] button is lit ambe
r, and playback starts.
To stop playback, press the
[STOP], [SHTL], [JOG],
[CUE], [REW], [FF], or [ALL STOP] button.
Video playback operations
Operate using the following buttons.
To change the playback speed
Press the [VAR] button, [JOG] button, or [SHTL] button,
t
hen turn the Z-ring. Play back in the normal direction
when you turn the Z-ring clockwise, and in the reverse
direction when you turn it counterclockwise.
[VAR] button: Variable-speed playba
ck in variable
mode. The playback speed is in the range –1 to +3
times normal speed corresponding to the angle of the
Z-ring.
[JOG] button: Variab
le-speed playback in jog mode.
The playback speed corresponds to the speed of
rotation of the Z-ring.
[SHTL] button: Variable
-speed playback in shuttle
mode. The playback speed corresponds to the angle
of rotation of the Z-ring.
Device control block display
In the device control block of the ICP-X7000, the display
shows the following information.
• FILE: Name of recalled content
• CRNT: Current playback position timecode
(h
our:minute:second:frame)
• START: Playback start point timecode
(h
our:minute:second:frame)
No. Parameter Adjustment
2 FM1 Speed Playback speed (0% to 200%)
Note
Notes
Note
Button Operation
FM LOOP Repeat (loop) playback
START TC Set current position as playback start point
STOP TC Set current position as playback stop point
STOP Pause playback
CUE Move to video playback start point
REW Move to start of video content
PLAY Playback
FF Move to end of video content
VAR Variable-speed playback in variable mode
JOG Variable-speed playback in jog mode
SHTL Variable-speed playback in shuttle mode
ALL STOP All stopped
To Next Page
Loading...
