What to do if Steris Basil 4600 shows STOP BUTTON PRESSED?
If the Steris Washer displays 'STOP BUTTON PRESSED! PUSH START TO RESUME ...' and the printer indicates 'ALARM: HH:SS:MM STOP BUTTON PRESSED!', it means the STOP/RESET touch pad was activated. To resume the cycle, press the CYCLE/START touch pad. Alternatively, press the STOP/RESET touch pad again to abort the cycle.
Why does my Steris Basil 4600 Washer show SUMP TOO LONG IN FILL?
If the Steris Washer displays 'SUMP TOO LONG IN FILL' and the printer prints 'ALARM HH:MM:SS SUMP TOO LONG IN FILL', it could be due to a few reasons. First, ensure that the supply valves are fully open. Second, foam in the chamber may be the cause, try rinsing the chamber with cold water and decreasing the detergent injection rate. If the issue continues, it's best to contact Service.
What causes SUMP FAILED TO REACH TEMP on Steris Basil 4600 Washer?
If the Steris Washer displays 'SUMP FAILED TO REACH TEMP' and the printer prints 'ALARM HH:MM:SS SUMP FAILED TO REACH TEMP', several factors could be responsible. First, ensure the steam supply valve is fully open. Next, consider if the temperature setting is too high and decrease the programmed temperature setpoint. Also, inspect the connections between the sump RTD sensor and control, tightening if necessary. Partially close the damper if it’s opened too wide. Ensure that the dynamic steam pressure matches the specifications on the equipment drawing. Clean the faulty RTD sensor in the chamber sump as needed. If the problem persists, contact Service.
How to fix ALK. TANK TOO LONG IN FILL error on Steris Basil 4600 Washer?
If the Steris Washer displays 'ALK. TANK TOO LONG IN FILL' and the printer prints 'ALARM HH:MM:SS ALK. TANK TOO LONG IN FILL', check if the hot water supply valve is closed and open the building and washer supply valves. Ensure the manual drain valve is closed. Verify the operation of the water level float ball and clean it if necessary. Increase the building water supply pressure if it is too low. If the issue continues, contact Service.
What to do if Steris Basil 4600 Washer displays SUMP TOO LONG IN DRAIN?
If the Steris Washer displays 'SUMP TOO LONG IN DRAIN' and the printer prints 'ALARM HH:MM:SS SUMP TOO LONG IN DRAIN', the self-cleaning screen may be clogged. Remove any debris from the screen. If the situation reoccurs, contact Service.
What to do if Steris Basil 4600 Washer displays LOAD DOOR OPEN WHEN PROCESSING?
If the Steris Washer displays 'LOAD DOOR OPEN WHEN PROCESSING' and the printer prints 'ALARM HH:MM:SS LOAD DOOR OPEN WHILE PROCESSING', it means the load-side door is open. Close and latch the door, then press the CYCLE/START touch pad to resume the cycle. If the condition reoccurs, call Service.
What to do if Steris Basil 4600 Washer displays UNLOAD DOOR OPEN WHEN PROCESSING?
If the Steris Washer displays 'UNLOAD DOOR OPEN WHEN PROCESSING' and the printer prints 'ALARM HH:MM:SS UNLOAD DOOR OPEN WHILE PROCESSING', it indicates that the unload-side door is open. Ensure the door is closed and latched, then press the CYCLE/START touch pad to resume the cycle. If the issue persists, contact Service.
What does ALK. TANK RTD FAILURE mean on my Steris Basil 4600 Washer?
If the Steris Washer displays 'ALK. TANK RTD FAILURE' and the printer prints 'ALARM HH:MM:SS ALK. TANK RTD FAILURE', the RTD sensor in the detergent tank may be faulty. Clean the sensor as necessary. If the situation reoccurs, contact Service.
What does SUMP RTD FAILURE mean on Steris Basil 4600 Washer?
If the Steris Washer displays 'SUMP RTD FAILURE' and the printer prints 'ALARM HH:MM:SS SUMP RTD FAILURE', it indicates a faulty RTD sensor in the chamber sump. Clean the sensor as necessary. If the situation reoccurs, contact Service.
To Next Page
General
