What to do if Struers LaboPol-60 Laboratory Equipment specimen mover head does not rotate?
If the specimen mover head on your Struers Laboratory Equipment does not rotate, check if the switch is set to “off”. If rotation is required, set the switch to “on.”
Defines the intended purpose and usage environment of the machine.
Outlines specific safety measures and potential risks associated with the LaboPol-60.
Lists general safety rules for installation, operation, and maintenance of the machine.
Explains the meaning of hazard and general message symbols used in the manual.
Details specific safety messages like DANGER, WARNING, CAUTION, and CRUSHING HAZARD.
Provides a general overview of the LaboPol-60 machine and its components.
Illustrates and labels the front view of the LaboPol-60 machine.
Describes different control panels and specimen movers that can be mounted on the machine.
Illustrates and labels the rear view of the LaboPol-60 machine.
Details guidelines for safely transporting the machine.
Provides instructions for storing or shipping the machine for extended periods.
Guides the user through the unpacking process of the machine.
Lists the items included in the packing box to verify completeness.
Provides instructions and safety precautions for lifting the machine.
Specifies the ideal placement requirements and environmental conditions for the machine.
Details the requirements and connection procedures for the machine's power supply.
Covers the necessary water supply and outlet connections for the machine.
Explains the installation and connection of an optional recirculation cooling unit.
Details the procedure for installing the preparation discs onto the machine.
Discusses noise levels and precautions during operation.
Addresses vibration levels and handling during manual preparation.
Covers the installation process for the LaboUI accessory.
Explains how to operate the LaboUI accessory.
Describes the functions of the LaboUI control panel buttons.
Explains how to use the water tap for automatic and manual water application.
Details how to use the spin function for drying discs.
Describes the use of splash guards for manual preparation and wet grinding.
Guides on performing manual preparation with the LaboUI.
Explains how to start, stop, and use the emergency stop function.
Illustrates and labels the front view of the LaboForce-50.
Illustrates and labels the rear view of the LaboForce-50.
Identifies the components of the specimen mover.
Covers the installation process for the LaboForce-50.
Explains how to install and adjust the specimen mover plate.
Explains how to operate the LaboForce-50 accessory.
Describes the functions of the LaboForce-50 control panel buttons.
Explains how to use the water tap for automatic and manual water application.
Details how to use the spin function for drying discs.
Describes the use of splash guards for different preparation types.
Guides on how to insert specimens into the mover plate.
Explains how to adjust the force applied to the specimen.
Guides on performing manual preparation with the LaboForce-50.
Explains how to start, stop, and use the emergency stop function.
Guides on how to remove specimens after preparation.
Explains how to change the specimen mover plate for different specimen diameters.
Illustrates and labels the front view of the LaboForce-100.
Covers the installation process for the LaboForce-100.
Describes the specimen mover for LaboForce-100 and its use with plates/holders.
Explains how to operate the LaboForce-100.
Describes the functions of the LaboForce-100 control panel buttons.
Explains how to use the water tap for automatic and manual water application.
Details how to use the spin function for drying discs.
Describes the use of splash guards for different preparation types.
Explains the LaboForce-100 display and its interface.
Outlines the options available in the main menu of the LaboForce-100.
Explains how to navigate through the LaboForce-100 display using the control knob.
Guides on how to change settings and text values on the LaboForce-100.
Covers initial software setup and settings for the LaboForce-100.
Explains how to configure user surfaces and general options.
Lists options available in the maintenance menu for LaboForce-100.
Details how to reset the configuration to factory default settings.
Explains the different preparation modes available on the LaboForce-100.
Explains how to start, pause, and stop the preparation process.
Illustrates and labels the front view of the LaboForce-Mi.
Illustrates and labels the rear view of the LaboForce-Mi.
Covers the installation process for the LaboForce-Mi.
Identifies the components of the LaboForce-Mi specimen mover.
Explains how to operate the LaboForce-Mi.
Describes the functions of the LaboForce-Mi control panel buttons.
Explains how to use the water tap for automatic and manual water application.
Details how to use the spin function for drying discs.
Describes the use of splash guards for different preparation types.
Guides on how to insert specimens into the mover plate.
Explains how to adjust the force applied to the specimen.
Explains how to use forced rotation for specimens.
Guides on performing manual preparation with the LaboForce-Mi.
Explains how to start, stop, and use the emergency stop function.
Guides on how to remove specimens after preparation.
Explains how to change the specimen mover plate for different specimen diameters.
Illustrates the LaboDoser-10 mounted on a LaboPol.
Illustrates the LaboDoser-10 on a table stand.
Guides the user through unpacking the LaboDoser-10.
Lists items included in the LaboDoser-10 packing box.
Covers the installation process for the LaboDoser-10.
Explains how to operate the LaboDoser-10 dispenser.
Guides on how to change the consumable bottles.
Illustrates and labels the front view of the LaboDoser-100.
Illustrates and labels the rear view of the LaboDoser-100.
Covers the installation process for the LaboDoser-100.
Explains how to operate the LaboDoser-100 via LaboForce-100.
Guides on how to change consumable bottles for the LaboDoser-100.
Details the procedure for cleaning tubes between different lubricants/suspensions.
Explains how to replace pump tubes with silicone ones.
Recommends regular cleaning for machine longevity and safe operation.
Outlines daily maintenance tasks for the machine.
Outlines weekly maintenance tasks for the machine.
Outlines monthly maintenance tasks.
Outlines annual maintenance tasks.
Information on ordering spare parts and technical questions.
Recommends regular service checks and outlines service procedures.
Covers proper disposal methods for the equipment and consumables.
Lists common errors, their causes, and solutions for LaboPol-60.
Lists common errors, their causes, and solutions for LaboForce-50.
Lists common errors, their causes, and solutions for LaboForce-100.
Explains error messages and their classification for LaboForce-100.
Lists common errors, their causes, and solutions for LaboForce-Mi.
Presents detailed technical specifications for the LaboPol-60.
Specifies safety circuit categories and performance levels for the machine.
Details the noise and vibration emission levels of the machine.
Identifies safety-related control system parts and replacement guidelines.
Lists available diagrams for the machine and its units.
Provides FCC compliance notice and regulatory information.
Lists required accessories, consumables, and their usage recommendations.
Details the dimensions and weights of the packaged equipment.
Specifies supply requirements, ambient conditions, and table load capacity.
Provides overall dimensions of the LaboPol with optional accessories.
Specifies the necessary clearance around the machine for operation and servicing.
Outlines guidelines for moving, storing, or shipping the machine.
Guides the user through the unpacking process.
Provides instructions and safety precautions for lifting the machine.
Details the requirements and connection procedures for the machine's power supply.
Details water supply connection requirements and notes.
Lists specifications for compressed air supply, required for LaboForce-100.
Provides recommendations and specifications for the recirculation cooling unit.
General| Max Sample Diameter | 60 mm |
|---|---|
| Wheel Diameter | 200 mm |
| Rotation Speed | 50-600 rpm |
| Power Supply | 230 V, 50/60 Hz |
| Motor Power | 0.25 kW |
| Type | Polishing machine |
To Next Page