Temptronic ThermoStream TP04100A - Figures; Tables

Preparation for Use
TP04100A Interface & Applications
Rev A: 0611 5/98
2-17.2.3 T-type Sensor: Disc Style (Supplied) .............................................................................................................. 2-33
2-17.2.4
T-type Sensor: Spring Style (Optional) ........................................................................................................... 2-33
2-17.2.5
K-type Sensor .................................................................................................................................................. 2-34
2-1 7.3 Alternative Thermocouple Attachment..
............................................................................................... 2-35
2-1 7.3.1 Thermocouple Construction and Attachment Guidelines ................................................................................ 2-35
2-17.3.2
Alternative Thermocouple Attachment Techniques ........................................................................................ 2-36
2-
1 8 REMOTE CONTROL COMMUNICATIONS ......................................................................................................... 2-3 8
2-18.1 IEEE-488.2 Interface
............................................................................................................................ 2-38
2-1 8.2 RS232C Interface
.................................................................................................................................. 2-38
2-18.3 ST/EOT/SFF Interface..
........................................................................................................................ 2-38
2-1 8.4 ~hermo~omm@ Software (optional)
.................................................................................................... 2-38
2-
19 INITIAL START-UP, CHECK OUT, SHUT DOWN ......................................................................................... 2-40
2-19.1 Main Power Switch
............................................................................................................................... 2-40
2-19.2 Startup
by Power ON.. .......................................................................................................................... 2-41
2-19.3 Initial Check Out
.................................................................................................................................. 2-41
2-19.4 Shutdown
by Power OFF ..................................................................................................................... 2-41
2-20
REPACKAGING ............................................................................................................................................... 2-42
2-2 Figures
FIGURE 2- 1 TP04 100A N PACKING CARTON FOR SHIPMENT. ................................................................................. 2-3
FIGURE 2-2 PLACEMENT CLEARANCES FOR TP04 I OOA ......................................................................................... 2-5
FIGURE 2-3 UNPACKING TP04 100A: BASE CONTROLLER, ARM & CLAMPS (OPTIONAL), THERMAL CAP (OPTIONAL),
AIR LINE U-CLAMP, POWER CORD
............................................................................................................ 2-8
FIGURE 2-4 THERMAL CAP ATTACHMENT (OPTIONAL TRANSPARENT CAP SHOWN) ............................................ 2- 12
FIGURE 2-5 THERMAL WAND: AIR PURGE OUTLET FITTING ................................................................................. 2- 13
FIGURE 2-6 THERMAL WAND STAND: ASSEMBLE SUPPORT COLUMN ................................................................... 2-1 5
...................................................... FIGURE 2-7 THERMAL WAND STAND: ASSEMBLE HORIZONTAL ARM, LOCKS
2-16
FIGURE 2-8 THERMAL WAND: INSULATION/HEAT SHIELD. ................................................................................ 2- 17
FIGURE
2-9 SYSTEM INPUTIOUTPUT (REAR PANEL) .............................................................................................. 2- 18
FIGURE 2- 10 THERMOCOUPLE SOCKETS: DUT T, DUT K (FRONT PANEL) ............................................................. 2-1 8
.......................................
FIGURE 2- 11 TYPICAL TEST SITE: HEAD, CAP, SHROUD, DUT, AIR PURGE MANIFOLD
2-26
FIGURE 2- 12 TYPICAL INSULATION FOR DUT ....................................................................................................... 2-27
FIGURE 2- 13 DUT TEST FIXTURE INTERFACE ....................................................................................................... 2-3 1
FIGURE
2- 14 ALTERNATIVE THERMOCOUPLE ATTACHMENT ............................................................................... 2-36
............................. ........................................................................................
FIGURE 2-15 MAIN POWER SWITCH
2-40
2-3 Tables
Page 2-2 41 IA-S2F.doc
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com